E6C2-CWZ3E 2500P/R
Note: Origin Indication
The following illustration shows the relationship between phase Z and the origin. Set cut face D to the phase Z origin as shown in the illustration.
*1. An inrush current of approximately 9 A will flow for approximately 0.3 ms when the power is turned ON.
*2. The line driver output is a data transmission circuit compatible with RS-422A and long-distance transmission is possible with a twisted-pair cable.(AM26LS31
equivalent)
*3. The maximum electrical response speed is determined by the resolution and maximum response frequency as follows:
① 配线应在电源OFF状态下进行,电源接通时,若输出线接触电源,则有时会损坏输出回路。 ② 若配线错误,则有时会损坏内部回路,所以配线时应充分注意电源的极性等。 3 若和高压线、动力线并行配线,则有时会受到感应造成误动作成损坏,所以要分离开另行配线。 ④ 延长电线时,应在10m以下。并且由于电线的分布容量,波形的上升、下降时间会较长,有问题时,采用施密特回路等对波形进行整形。
输出开始、
结束时间
1μs以下
(控制输出电压:5V负载电
阻1kΩ、导线长度:2m)
1μs以下
(导线长度:2m 负载电流:10mA)
0.1μs以下
(导线长度:2m
IO = -20mA、IS = 20mA)
E6C2-CWZ3E 1024P/R Ambient temperature range Operating: −10 to 70°C (with no icing), Storage: −25 to 85°C (with no icing) Ambient humidity range Operating/Storage: 35% to 85% (with no condensation) Insulation resistance 20 MΩ min. (at 500 VDC) between current-carrying parts and case Dielectric strength 500 VAC, 50/60 Hz for 1 min between current-carrying parts and case Vibration resistance Destruction: 10 to 500 Hz, 150 m/s 2 or 2-mm double amplitude for 11 min 3 times each in X, Y, and Z directions Shock resistance Destruction: 1,000 m/s 2 3 times each in X, Y, and Z directions Degree of protection IEC 60529 IP64, in-house standards: oilproof Connection method Pre-wired Models (Standard cable length: 2 m) Material Case: Zinc alloy, Main unit: Aluminum, Shaft: SUS420J2 信号输出有正弦波(电流或电压),方波(TTL、HTL),集电极开路(PNP、NPN),推拉式多种形式,其中TTL为长线差分驱动(对称A,A-;B,B-;Z,Z-),HTL也称推拉式、推挽式输出,编码器的信号接...
E6C2-CWZ5B 60P/R Maximum response frequency*3 100 kHz 50 kHz 100 kHz Phase difference between outputs 90°±45° between A and B (1/4 T ± 1/8 T) Rise and fall times of output 1 μs max. (Control output voltage: 5 V, Load resistance: 1 kΩ, Cable length: 2 m) 1 μs max. (Cable length: 2 m, Sink current: 10 mA) 0.1 μs max. (Cable length: 2 m, IO = −20 mA, IS = 20 mA) Starting torque 10 mN·m max. Moment of inertia 1×10 −6 kg·m2 max.; 3 × 10 −7 kg·m2 max. at 600 P/R max. Shaft loading Radial 50 N Thrust 30 N Maximum permissible speed 6,000 r/min Protection circuits Power supply reverse polarity protection, Load short-circuit protection OMRON编码器是用来测量转速的装置,光电式旋转编码器通过光电转换,可将输出轴的角位移、角速度等机械量转换成相应的电脉冲以数字量输出(REP)。它分为单路输出和双路输出两种。技术参数主要有每转脉冲数(几十个到几千个都有),和供电电压等。单路输出是指旋转编码器的输出是一组脉冲,而双路输出...