E6C2-CWZ1X 200P/R
负荷还大的负荷,或造成拨芯现象,因此,要特别注意。 轴承寿命与使用条件有关,受轴承荷重的影响特别大。如轴承负荷比规定荷重小,可大大延长轴承寿命。 不要将旋转编码器进行拆解,这样做将有损防油和防滴性能。防滴型产品不宜长期浸在水、油中
90°±45° between A and B (1/4 T ± 1/8 T)
允许转速
6,000r/min
保护回路
负载短路保护、电源反接保护
-
环境温度范围
工作时:-10~+70°C、保存
Rise and fall times of
output
1 μs max.
(Control output voltage: 5 V, Load
resistance: 1 kΩ, Cable length:
2 m)
1 μs max.
(Cable length: 2 m, Sink current: 10 mA)
0.1 μs max.
(Cable length: 2 m, IO = −20 mA,
IS = 20 mA)
Starting torque 10 mN·m max.
Moment of inertia 1×10
−6
kg·m2
max.; 3 × 10
−7
kg·m2
max. at 600 P/R max.
E6C2-CWZ5G 1200P/R 0r/min 保护回路 负载短路保护、电源反接保护 - 环境温度范围 工作时:-10~+70°C、保存时:-25~+85°C (无结冰) 环境湿度范围 工作时、保存时:各35~85%RH (无结露) Ω min. (at 500 VDC) between current-carrying parts and case Dielectric strength 500 VAC, 50/60 Hz for 1 min between current-carrying parts and case Vibration resistance Destruction: 10 to 500 Hz, 150 m/s 2 or 2-mm double amplitude for 11 min 3 times each in X, Y, and Z directions Shock resistance Destruction: 1,000 m/s 2 3 times each in X, Y, and Z directions Degree of protection IEC 60529 IP64, in-house standards: oilproof Connection method Pre-wired Models (Standard cable length: 2 m) 可能会损坏内部功能,使用上应充分注意。安装 安装时不要给轴施加直接的冲击。 编码器轴与机器的连接,应使...
E6C2-CWZ5G 3000P/R 100kHz 50kHz 100kHz 输出相位差 A相、B相的位相差90°±45° (1/4T±1/8T) 输出开始、 结束时间 1μs以下 (控制输出电压:5V负载电 阻1kΩ、导线长度:2m) 1μs以下 (导线长度:2m 负载电流:1 3 × 10 −7 kg·m2 max. at 600 P/R max. Shaft loading Radial 50 N Thrust 30 N Maximum permissible speed 6,000 r/min Protection circuits Power supply reverse polarity protection, Load short-circuit protection --- Ambient temperature range Operating: −10 to 70°C (with no icing), Storage: −25 to 85°C (with no icing) ① 配线应在电源OFF状态下进行,电源接通时,若输出线接触电源,则有时会损坏输出回路。 ② 若配线错误,则有时