美国BC U-2400电刀分析仪
型号：BC U-2400 类别： 质控仪器 品牌：美国BC pdf资料: 美国BC U-2400电刀分析仪.pdf
美国BC U-2400电刀分析仪详细介绍：
美国BC
U-2400电刀分析仪是一种高，真实的RMS测量系统，用于电发生器的校准和常规性能验证。它提供比以前可以使用传统电单元分析仪
设计更高的准确度。U-2400提供的低电内部负载组，范围为0至6400欧姆，单位为1欧姆。它是基于微处理器的，并且利用的硬件和软件
的组合来提供准确的测试结果，甚至从“嘈杂”的U发生器波形，如“喷雾”。在U-2400中使用的待定DFA?技术允许系统对电发生
器产生的复杂RF波形进行大量数字化，
U-2400电刀分析仪
美国BC
U-2400电刀分析仪与许多传统的U分析仪不同，U-2400具有内部HV设置继电器来控制测量路径，允许用户在功率测量，泄漏测
量，CQM / RECQM / ARM测试之间切换，甚至运行可能包括任何或这些测试 - 甚至没有移动的电线。
美国BC U-2400电刀分析仪内部的电流互感器检测流过内部测试负载的RF电流，并产生由微处理器数字化和分析的比例电压。使用电流互感器组合U-2400的标准和低范围，用户可以控制从类型的电发生器获得高和高分辨率读数的能力。
美国BC U-2400电刀分析仪主要功能：
? 使用DFA?技术的真值读数
? 行业标准电流检测技术
? mV，mV峰值，ma，波峰因数和功率（瓦数）范围
? 带触摸屏的彩色QVGA显示屏
? 读数测量的1％
? 数字校准 -转
? 可选的显示选项
? 测量RF信号的图形屏幕上表示
? 标准（1000毫伏）和低范围（100毫伏）与自动缩放能力
? 通过某些电制造商提供的用于低工作周期脉冲输出脉冲RF波形测量模式
The Model U-2400 Electrosurgical Unit yzer is a high-accuracy,
true RMS RF measurement system digned to be used in the calibration
and routine performance verification of Electrosurgical Generators. It
offers a higher degree of accuracy than previously attainable with
conventional Electrosurgical Unit yzer digns. The U-2400
provid an advanced low reactance internal load bank with a range of 0
to 6400 ohms in 1 ohm increments. It is microprocsor-based and
utiliz a combination of unique hardware and software to provide
accurate and reliable tt rults, even from “noisy” U Generator
waveforms such as “Spray”. The Patent Pending DFA? Technology utilized
in the U-2400 allows the system to aggrsively diize the complex
RF waveforms produced by Electrosurgical Generators, yze each
individual dial data point and provide highly accurate measurement
rults.
The U-2400, unlike many conventional U yzers, has internal HV
setup relays to control the measurement path, allowing the user to
switch between power measurements, leakage measurements, CQM/RECQM/ARM
tting or even run an autosequence that could include any or all of
the tts – without even moving wir around.
The current transformer internal to the U-2400 sens the RF current
flowing through the internal tt load and produc a ratiometric
voltage which is diized and yzed by the microprocsor. Combining
the standard and low rang of the U-2400 with the use of the current
transformer, the user has full control over the ability to get high
accuracy and high rolution readings from all t of Electrosurgical
Generators.
The following are some of the main featur:
? True RMS readings using DFA? technology
? Industry standard current sensing technology
? mV, mV peak, ma, crt factor and power (wattage) rang
? Color QVGA display with touchscreen
? 1% of reading measurement accuracy
? Dial calibration – no pots to turn
? Selectable display options
? Graphical on-screen reprentation of measured RF signal
? Standard (1000 mV) and low range (100 mV) with autoscaling capability
? Pulsed RF waveform measurement mode for low duty cycle pulsed outputs offered by some electrosurgical manufacturersSAG:
U-2400电刀分析仪,U-2400,美国BC U-2400电刀分析仪,BC U-2400
