出厂简况：
DZL型链条炉排卧式快装锅炉出厂时，分件包装如下：
1.锅炉大件是包括锅炉本体，链条炉排煤斗、看火孔、拨火门、前后烟箱、炉墙、保温层的组合件。
2.调速箱传动装置，包括电动机等。
3.鼓风机：包括电动机、鼓风机座和进风接管等。
4.引风机：包括电动机、轴承座及烟道连接管等。
5.刮板出渣机：包括电动机。
6.平台扶梯和栏杆。
7.除尘器：包括除尘器支架、集灰斗、地脚螺栓等。
8.烟囱。
9.给水设备及阀门仪表、管道件。
10.电控柜。
11.上煤机：（用户自选）。
12.有二台或二台以上锅炉同时安装时应注意鼓风机（包括鼓风机座和接口）引风机（包括进风管）省煤器等组件的记号（锅炉出厂编号）与锅炉上的记号相同。
13.随炉文件：有总图、主体、本体、筒体、炉墙、管道仪表阀门、保温层、地基图、链条炉排、平台扶梯、烟囱、易损件图纸及受压元件强度计算、安装使用说明书、锅炉总清单各二份，产品监检质量证明书一份。
安 装 说 明：
四.安装前的准备工作：
当锅炉运到使用现场后，为了能运行，安装前须做好以下准备工作：
1.确定安装公司，核实资质证明。组织及人员配备：
锅炉安装单位须有上级主管部门颁发的合安装范围的锅炉安装资格证书，负责与当地锅炉监督机构取得联系，填写安装告知书，并接受当地锅炉检验检测单位的安装监检。安装完工后，安装单位和当地锅炉监督机构共同进行安装质量验收。并按有关规定及时办理锅炉使用登记入户手续。锅炉使用单位应有专人负责锅炉安装工作，锅炉安装时需有司炉参加，并配有管工、钳工、起重工、冷作工、电焊工及辅助工。
Factory profile:
DZL te chain grate horizontal packaged boiler factory, component packaging are as follows:
1 big is the boiler comprises a boiler body, a chain grate coal scuttle, see the fire hole,embly poke door, front and back oke boxes, furnace wall, thermal insulationlayer.
The 2 speed box drive device comprises a motor, etc..
3: including motor, blower blast base and inlet connecting pipe etc..
4 fan: including motor, bearing seat and a flue connecting pipe etc..
The 5 scraper deslagging machine: including motor.
6 platform and ladders and railings.
7: dust collector comprises a dust collector, a dust collecting bucket bracket, anchor bolt etc..
8 chimneys.
9 water supply equipment and valves and instruments, piping parts.
10 cabinet.
11 coal machine: (option).
12 there are two or more than two boilers at the same time the installation should pay attention to the blower (including blast base and interface) fan (including air inlet pipe)economizer embly mark (boiler factory number) with the same mark on the boiler.
13 documents: general layout, with the furnace body, body, cylinder body, furnace wall, piping and instrumentation valves, heat preservation layer, foundation drawing,chain grate, platform and ladders, chimney, wearing parts drawings and compression parts strength calculation, installation instructions, boiler general list of all two copies,a product quality inspection certificate.
The installation instructions:
Four pre installation preparation work:
When the boiler is transported to the use of the site, in order to ensure that canquickly run, must do the following preparation before installation:
1 determine the installation company, to verify the qualification certificate.Organization and staffing:
Boiler installation units must be issued by the higher competent departments withboiler installation range installation qualification certificate, is responsible for thecontact with the local boiler vision mechani, fill in the installation of this book,and accept the local boiler inspection testing unit installation inspection. After the installation is completed, the installation unit and local boiler vision agency jointinstallation quality acceptance. And according to the relevant provisions of the timely processing of boiler use registration formalities. Boiler unit should be specifically responsible for the boiler installation work, boiler installation is required to have a fireman in, and is equipped with the foreman, fitter, welder rigger, cold work, and auxiliary industry.
