本仪器 用于检测玩具可触及到的位置是否存在危害的锐利尖点。
合标准：16 CFR 1500.48 ASTM F 963 4.8 EN.12 操作原理：试验器有槽端有一宽0.04英寸长0.045英寸的矩形开口, 两个参考尺寸尖锐度由被测该口的深度为0.015英寸深处的传感头, 并能克服弹力为0.5磅的弹簧使传感头再移动0.005英寸, 即被确认为尖锐点. 要求：槽开口不大于0.040×0.045英寸, 触及深度不小于0.015英寸, 作用力不过1磅.：测试方法
1.尖点测试器调校程序
a.顺时针旋转/松开/锁环。
b.顺时针转动尾盖，直到红色指示灯亮。
c.逆时针慢慢转动尾盖，直到指示灯刚好熄灭。
d.向前/后转动尾盖，确定指示灯刚好亮时确切位置。
e.参考尾盖上的微米刻度线标注校正的位置。
f.逆时针转动尾盖5格刻度线（帽上两短线之间的距离为一格）。
g.扭紧锁环，直至紧靠尾盖。
2.尖点测试程序
a.样品在进行尖点测试前须在室温为23±2℃、湿度为20%～70%的环境内放置4小时。
b.将放入尖点测试器测量槽内/握住测试物/垂直自由的施加共重1LBS（4.5N）的力，通过测试量槽位至测试。
判定：测试灯亮则为不合格
仪器型号：KXM20
The instrument for the detection of toys can be touched to the location of the existence of a risk of injury due to sharp cusp.
合标准：16 CFR 1500.48 ASTM F 963 4.8 EN.12
Standard: 16 CFR 1500.48 ASTM F 9634.8 EN.12
操作原理：试验器有槽端有一宽0.04英寸长0.045英寸的矩形开口, 两个参考尺寸尖锐度由被测该口的深度为0.015英寸深处的传感头, 并能克服弹力为0.5磅的弹簧使传感头再移动0.005英寸, 即被确认为尖锐点. 要求：槽开口不大于0.040×0.045英寸, 触及深度不小于0.015英寸, 作用力不过1磅.：
Operating principle: the tester with a grooved end has a width of 0.04 inches long and 0.045 inches rectangular openings, two reference dimensions sharpness of a measured tip is inserted into the mouth of the depth sensing head 0.015 inches deep, and can overcome the elastic force of spring 0.5 pounds of the sensing head to move 0.005 inches, which is confirmed as the sharp. Requirements: slot opening is not greater than 0.040 x 0.045 inches, touch the depth of not less than 0.015 inches, force does not exceed 1 pounds:
测试方法
Test method
1.尖点测试器调校程序
1 sharp point tester calibration procedure
a.顺时针旋转/松开/锁环。
A. clockwise / release / lock ring.
b.顺时针转动尾盖，直到红色指示灯亮。
B. clockwise rotating tail cover, until the red indicator light.
c.逆时针慢慢转动尾盖，直到指示灯刚好熄灭。
C. clockwise slowly turn the tail cover, until the light was extinguished.
d.向前/后转动尾盖，确定指示灯刚好亮时确切位置。
D. forward / back turn tail cover, determine the indicator lamp just bright when the exact location.
e.参考尾盖上的微米刻度线标注校正的位置。
The E. reference tail cover on the micron scale line marking the location correction.
f.逆时针转动尾盖5格刻度线（帽上两短线之间的距离为一格）。
F. counterclockwise tail cover 5 grid scale line (Cap two short distance as one).
g.扭紧锁环，直至紧靠尾盖。
G. screw lock ring, until close to the tail cover.
2.尖点测试程序
Test procedure 2 cusps
a.样品在进行尖点测试前须在室温为23±2℃、湿度为20%～70%的环境内放置4小时。
In the A. sample were sharp point testing must be at room temperature is 23 ± 2 ℃, humidity 20% ~ 70% environment placed within 4 hours.
b.将放入尖点测试器测量槽内/握住测试物/垂直自由的施加共重1LBS（4.5N）的力，通过测试量槽位至测试。
B. will tip into the sharp point tester measuring tank / hold test / vertical free applied a total weight of 1LBS (4.5N) force, through measuring slot to test tip.
判定：测试灯亮则为不合格
Judge: test lights for unqualified
仪器型号：KXM20
The instrument model: KXM20
