中性包装 高测酒器 酒精测试仪AT6000，rgknse

隆客色！！

TEL:

产品名称：洒精测试仪

型号：AT6000

AT6000呼出气体酒精含量探测器是专用于测试人体呼出气体中酒精含量的仪器。本机敏感元件采用汉威电子先进的纳米半导体酒精传感器，具有极好的灵敏度和出色的重复性；测试程序由人工智能设计的微电脑控制，工作流程合理，简洁便利，功能齐全，具有多种自适应能力；背光照明的LCD数码、字图显示，直观清晰；小巧的便携设计更便于您移动使用。当被测呼出气体中的酒精含量超过预定值时，本机会自动发出声音报警，为您的安全多一份提醒。

【产品主要技术参数】

【型   号】AT6000

【传感器类型】 纳米半导体酒精传感器

【工作电压】 DC4.5V（3×AAA电池）

【欠压指示】 Vcc＜3.30V±0.10V显示欠压；Vcc＜3.00V±0.10V欠压关机

【工作电流】 ≤120mA

【使用环境】 温度： -10℃～50℃      相对湿度：≤95%   无结露

【测试响应时间】 ＜5s

【预热时间】 ＜20s

【测量范围】 (0.00～1.00)mg/L(0.00～0.20%BAC；0.00～2.00mg/L)

【报警浓度】 0.24mg/L(0.05%BAC； 0.50g/L)

【精 确 度】 ±10% F.S

【报警方式】 声报警

【显示方式】 带蓝色背光的3位 LCD 数字配合图文显示

【重    量】 ≤64g  (不含电池)

【外形尺寸】 l×b×h，mm ：103×65×27

【颜    色】 黑色

使用说明：
按屏幕正面长按1-3秒“POWER”开机键进入约10秒的传感器预热倒计时过程。

当看到屏幕出现BIOW字样开始吹气 (向吹气孔连续吹气约3-6秒钟左右 进入约5秒的反应期同时测试结果会显示在LCD上，约5秒钟后自动关机。

将口部贴近呼气测试感应器，并连续3-6秒呼气到感应器内。

显示屏可读取测试结果。

当测试结果达到下列范围时，“Caution”“警告”字句便会显示
   √0.02% BAC(or 0.2g/l)to 0.05%
BAC(or 0.5g/l)
     0.05% BAC(or 0.5g/l)to 0.08% BAC(or 0.8g/l)

当测试结果达到下列的范围，“Danger""危险"字句便会显示。
   √over & EQUAL 0.05% BAC (or
0.5g/l)
     over & EQUAL 0.08% BAC (or 0.8g/l)

《机动车驾驶员驾车时血液中酒精含量规定》强制性全国标准:规定血液中酒精含量大于或等于0.2mg/ml时驾驶机动车为酒后驾车；大于或等于0.8mg/ml时驾驶机动车为醉酒驾车。

报警声音说明:
当测试结果比预设的报警点低,其差值大于0.2‰BAC时,数字显示测试结果,无报警声.
当测试结果比预设的报警点低,其差值小于或等于0.2‰BAC时,数字显示测试结果,有预报警声.(只有当报警点大于0.20‰BAC心上时才有此项功能.)

维护与保养
请勿使用苯、稀释剂或汽油等溶剂清洁本产品，以免损坏机体外壳。
防止跌落和强震，否则会导致本机故障。
除更换电池外，请勿尝试修理、改造或拆卸零件。
如果长时间不使用本产品时，请取出电池，以免因电池漏液而损坏本机。

本产品设计、制造、检验遵守以下国家标准：
GB/T21254-2007《呼出气体酒精含量检测仪》
GB19522-2004《车辆驾驶人员血液、呼气酒精含量阈值与检验》

特点:
◆ 先进的纳米半导体酒精传感器；
◆ 响应、恢复迅速、检测快捷方便；
◆ SMD装配工艺，性能稳定可靠；
◆
人工智能微电脑控制；
◆ 测试过程屏幕直观显示；
◆ 蓝色背光照明的LCD数码、字图显示；
◆ 便携设计、小巧轻便；
◆
酒精超限自动声报警；
◆ 传感器故障自检；
◆ 智能节电设计，电池欠压指示

产品使用

1   打开本机后壳的电池盖，将3节AAA、1.5V的电池按极性装入本机，然后再装上电池盖，即可投入使。
2  
按下“开机”键，伴随一短促蜂鸣声，背光点亮，同时屏幕显示从100到000的倒计时，屏幕下部显示“WAIT”字样,提示机器运行预热程序，此时请不要吹气，否则会影响测试。预热完毕，“WAIT”显示消失，探测器发出一声蜂鸣，同时显示“BLOW”字样，“C”字母游动显示，此时即可开始下一步的呼出气体酒精含量测试。

说明：预热过程中，倒计时速度与上次测试浓度有关，浓度越低，倒计时越快，否则越慢。

3   被测试者深吸气，当屏幕上“C”字母游动显示时对准本机吹嘴连续均匀吹气，直到本机发出一声蜂鸣，停止吹气。

4  
吹气结束，屏幕游动显示“”符号，同时显示“TEST”字样，提示正在分析测试结果，此时不要吹气，否则会影响测试结果。分析结束后屏幕上所显示的浓度值即为测试者呼出气体中的酒精含量，该值保持数秒之后，本机自动关机。

5   若要进行下测试，须重新按“开机”键，过程参照上述2～4。

使用说明

1、按动开关健，测试仪的LCD显示屏便会亮灯，同时会发出“咇”的一声。
2、数字亦会由10跳到0，便完成预热程序。
3、将口部贴近呼气测试感应器，并连续3-5秒呼气到感应器内。
4、显示屏可读取测试结果。
5、当测试结果达到下列范围时，“Caution”“警告”字句便会显示
  
√0.02% BAC(or 0.2g/l)to 0.05% BAC(or 0.5g/l)
     0.05% BAC(or 0.5g/l)to
0.08% BAC(or 0.8g/l)
6、当测试结果达到下列的范围，“Danger""危险"字句便会显示。
   √over &
EQUAL 0.05% BAC (or 0.5g/l)
     over & EQUAL 0.08% BAC (or
0.8g/l)
7、《机动车驾驶员驾车时血液中酒精含量规定》强制性全国标准:规定血液中酒精含量大于或等于0.2mg/ml时驾驶机动车为酒后驾车；大于或等于0.8mg/ml时驾驶机动车为醉酒驾车。

--------------------------------------------------------------------------------
[温馨提示]
·喝酒后，建议先稍待20分钟再检测，因为酒精需要约20分钟的时间从消化器官进入血液内，
 
而残留在口腔的酒精也需要时间消散。
·要得到更准确的结果，每次测试之间应距离少三分钟时间。
·请勿使用含苯，汽油及天拿水成份的产品清洁测试仪。
·请勿让任何液体渗进感应器内。
·梦王汽车用品专营店提醒您，为了您和他人的安全，请勿酒后驾车。

【产品图片展示】

Preface

Reminding Before your testing.

Alco Smart Breath tester should be used only to give an indication of the possible presence of alcohol in the breath/blood. You should not rely upon it as the sole basis to determine intoxication or whether it is safe to drive a vehicle, operate equipment, or engage in dangerous activities.

Everyone has different body responds to alcohol consumption and his testing result only as reference, not a subject standard for consequent decision.

The manufacture, importer or distributor takes no responsibility whatsoever for the use ofthis product for any reason. This product must not be used as a tool for determining whether a person is able to operate a motor vehicle or device legally or safely. The intake of any alcohol will impair reflexes and judgment to operate motor vehicle.

Before your testing, please view the manual carefully and follow the instruction strictly.

General Introduction

AT6000breath alcohol tester is kind of tester designed to measure concentration result of the breathed alcohol in the human body.This device adopts advanced flat surfaced alcohol sensor which has excellent sensitivity andreproducibility, fashional and portable design make it more convenient for personal use. When the alcohol content exceeds the preset limited level, this device would send an audio and videowarning to remind your safety.

Main Feature:

Advanced flat surfaced alcohol sensor

Quick response

SMD assembling, stable performance

Smart MCU control

Direct testing process LCD indication

Digital LCD display with light blue backup

Portable and fashion design?

Audio warning beyond pre-set limit

Sensor fault self checking?

Batterysaved design, low voltage indication

Technical Data

Sensor type: Flat surfaced alcohol sensor

Detection Range: 0.00 – 0.20BAC%; 0.00～2.00g/L；

0.00 – 2.00BAC‰；0.00 -1.00 mg/L; 0.00 – 200mg/100mL

Alarming Level: 0.05BAC%; 0.50g/L; 0.50 BAC‰; 0.25mg/L; 50mg/100mL

Accuracy: ±10% F.S

Working Voltage: DC4.5V（3×AAA）Batteries; Working Current: ≤120mA

Working Environment: Temperature -10℃～50℃

Relative Humidity ≤95% No Dews

Display: 3 digits LCD display with light blue backup

Dimension: 103×65×27mm (L×W×H), ≤64 g Battery excluded

Batteryexpectancy time: ≥200Times

Digital Indication:

2. Operation Instruction

2.1. Slide down the battery compartment on the back side, insert 3pcs AAA 1.5V batteries inside according to battery polarity indication and close it.

2.2. Press the switch button and last for 1s, the tester would be power on with a buzzer brief ringing, ‘Wait’ shows on down side of screen, meantime it shows 100 to 000 countdown, please wait now, otherwise its accuracy will be not good.

Until “Wait” disappears, tester will send out a ring,meantime shows “BLOW” and “C” gliding, now the test could begin.

Remarks: Its countdown speed will depend on concentration of last test, if concentration is high, it will be slow. If concentration is low, the countdown will be very quick.

2.3. Have a deep breath before testing, and blow directly to gas entry when “C”circularly shows, stop blow when heard its buzzer ring.

2.4. After blowing finished, the LCD screen willshow “ ” circularly, meantime shows “TEST”, this means the tester is analyzing the result, do not blow at this time. After analyze the screen will show the testing results.

It will turn off automatically after keep results for several seconds.

2.5. If a new testing needed, press the switch button again and repeat the above step 4.2～4.4.

3. Notification

3.1. Avoid any fall or strong shock.

3.2. If noise gas with high concentration existed,may the tester won’t work normally.

3.3. If testing is done under low voltage, certain error will be existed between the real value.

3.4. To ensure the testing result, please wait 15 mins to take the testing after your drinking.

3.5. The result may be unreliable for your first test if long time storage, please try second time.

3.6. Do not keep the tester in the environment of corrosive gas (Chlorine etc) for use or deposit, also in other bad surroundings.

3.7. Do not blow smoke to tester directly, especially the smokers.

3.8. When in consecutive testing, if blow immediately after drink, this concentration is very high, there will be some rudimental in mouthpiece. Please wait for at least 1 min to take second test, or, blow clean air for 3 seconds to clean out its mouthpiece.

3.9. After Long time use, there may be dirt on the tester, please use clean cloth to wipe off. Do not use any hard object or the solvent with any Corrosive ingredient.

Remarks: Common Fault and Solving solutions