| 类型 | 光学显微镜 | 品牌 | CLN |
| 型号 | CLN3-02 | 仪器放大倍数 | 400/200/100 |
| 目镜放大倍数 | 400/200/100 | 物镜放大倍数 | 400/200/100 |
| 重量 | 1（g） | 适用范围 | 光纤通信 |
| 装箱数 | 20 |
Axial Adjustment Te Video Fiber Microscopes
Specification: FVKⅣ-410P、FVKⅣ-210P、FVKⅣ-080P
Feature:
.
The cylindrical adjusting knobs on the X-axis and Y-axis enable adjustment in all directions
(5.5x4.0 mm)
. Multi-axial alignment
. High definition and high resolution
. You can fix the located fiber core images by rotating two disk-shaped adjusting knobs right at the right and bottom of the Adapter socket. This solves the problem that the original model cannot be fixed.
. During high magnification observation, you can test any part of the fiber endface, thus achieving a balance between broad vision and high definition.
. You can output images to a black and white monitor, or display them on a computer with a U device connected.
. With corresponding adapters supplied, you can test MTRJ (the lock pin te and finished product te), and MT/MPO/FA connectors.
. Applicable to manufacturers of MTRJ/MPO jumpers
. Video output 12V DC input Power switch power supply
Operation Manual for Bench- Video Fiber Microscopes
Ordinary Te Axial Adjustment Te Built-in Display Te
FVKI-410P FVKⅣ-410P FVKⅥ-410P
FVKI-210P FVKⅣ-210P FVKⅥ-210P
FVKI-080P FVKⅣ-080P
Technical Parameters
Magnification 50x , 80 x, 200 x, 400 x
System Resolution 0.7 um - 2.7 um
Field of View on 9” Monitors 0.18Χ0.235 mm - 3.56Χ4.81 mm
Standard Configuration of Adapter Interfaces For ordinary models,
check the PC endface of FC/SC/ST/LC/MU.
For specified models, check the specified endface.
Power Supply 220V 50HZ
Dimension (Main Unit) 230mmx81mmx126mm
Net Weight 1.3 kg (main unit), 6.2 kg (9’’ monitor)
Installation Steps:
Step 1: Connect one end of the video cable to the "Video Out" position of a bench-
video fiber microscope, and the other end to the "Video In" position of the monitor;
Step 2: Connect one end of the power adapter to the power supply (220V/110V), and the
other end to the "12V DC" position of the bench- video fiber microscope;
Step 3: Power on the monitor and the bench- video fiber microscope.
step 4:You can inspect the jumper when you use the adapter match to the jumper on the
Bench-
step 5: You can inspect the jumper when you use the adapter match to the jumper on
Axial Adjustment Te Video Fiber Microscopes . If you inpect the MTRJ ferrul and finished product te and MT/MPO , You must fix the adapter using the Allen screws and Allen Key .
Operations & Precautions
1. Insert a fiber connector into the adapter of a video fiber microscope.
2. Adjust the focal length of the video fiber microscope to make the image clear.
3. Adjust the contract and brightness of the monitor to optimize images.
4. During testing, you need not adjust the focal length (or only slightly adjust the focal length) to connect the fiber for checking.
5. The Adapter is worn out greatly if it has been used for a long time. If the bottom hole of the adapter does not hold the lock pin, the lock pin may directly contact the lens and cause damages accordingly. In this case, you need to replace the adapter.
6. Clean the lens of the fiber microscope to prevent dusts and residue and increase the service life.
7. The bench- axial adjustment te is applicable for MTRJ (the lock pin te and finished product te), and MT/MPO connectors. Instead of inserting or removing the connector, you only need to rotate the cylindrical adjusting knobs on the instrument to observe the two cores of MTRJR and the 12 cores of MPO
