E6H-CW6C 600P/R
使用时的注意事项
选用及使用本公司产品时请理解如下要点。
(1) 除了额定值、性能指标外,使用时还必须遵守“使用条件等”。
(2) 客户必须自己负责确认“适用性等”,然后判断是否选用“本公司产品”。“本公司”对“适用性等”不做任何保证。
(3) 对于“本公司产品”在客户的整个系统中的设计用途,必须由客户自己负责对是否已进行了适当配电、安装等进行事先确认。
(4) 使用“本公司产品”时,客户必须采取如下措施:(i)相对额定值及性能指标,必须在留有余量的前提下使用“本公司产品”,并采用冗余设计等安全设计(ii)所采用的安全
设计必须确保即使“本公司产品”发生故障时也可将“客户用途”中的危险降到最小程度、(iii)构建随时提示使用者危险的完整安全体系、(iv)针对“本公司产品”及“客户
用途”定期实施各项维护保养。
(5) “本公司产品”是作为用于一般工业产品的通用产品而设计生产的。因此,不是为如下用途而设计生产的
atings.
● Mounting
• The diameter of the mating shaft must be 8 mm and 8 to
11 mm long from the mounting surface.
• The allowable displacement in the mating shaft must 0.05 mm in
the radial direction and 0.3 mm in the thrust direction.
• The mounting surface and shaft must be perpendicular to within
0.03 mm.
•When securing the Encoder, do not allow force to be applied to the
E6H-CWZ6C 1000P/R 允许转速 10,000r/min 环境温度范围 工作时:-10~+70℃ (90%RH以下) 保存时:-30~+85℃ (不结冰) 环境湿度范围 工作时、保存时:各90%RH以下(不结露) 绝缘电阻 电容器接地的除外 耐电压 电容器接地的除外 C规格 IP50 连接方式 导线引出式(标准导线长 500mm) 材质 外壳 铁 本体 ...
E6H-CW6C 20P/R ) 300, 360, 500, 600, 720, 800, 1,000, 1,024, 1,200, 1,500, 1,800, 2,000, 2,048, 2,500, 3,600 Output phases Phases A, B, and Z Phases A, A, B, B, Z, and Z Output configuration Open-collector output Voltage output Line-driver output*4 Output capacity Applied voltage: 35 VDC max. Sink current: 35 mA max. Residual voltage: 0.7 V max. (at sink current of 35 mA) Output resistance: 1 kΩ Sink current: 30 mA max. Residual voltage: 0.7 V max. (at sink current of 30 mA) O 输出相 A相、B相、Z相 A相、A相、B相、B相、Z相、Z相 输出形式 集电极开路输出 电压输出 集电极开路输出 * 4 输出容量 外加电压:DC35V以下 同步电流:35mA以下 残留电源...