E6H-CWZ6C 150P/R
It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made.
However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or
establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual
specifications of purchased products.
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.
PERFORMANCE DATA
Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the
result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON
Warranty and Limitations of Liability
项目 型号
E6H-CWZ6C
E6H-CWZ3E
E6H-CWZ3X
电源电压
DC5V-5%~24V+15% 脉冲(p-p)5%以下
DC5V-5%~12V+10% 脉冲(p-p)5%以下
消耗电流 * 1
100mA以下
分辨率(脉冲/旋转)
300、360、500、600、720、800、1,000、1,024、1,200、1,500、1,800、2,000、2,048、2,500、3,600
输出相
A相、B相、Z相
A相、A相、B相、B相、Z相、Z相
输出形式
集电极开路输出
电压输出
集电极开路输出 * 4
输出容量
外加电压:DC35V以下 同步电流 :35mA以下 残留电源:0.7V以下 (同步电流35mA时)
输出电阻:1kΩ 同步电流 :30mA以下 残留电源:0.7V以下(同步电流30mA时)
E6H-CWZ6C 300P/R 大轴 负载 径向 29.4N 轴向 4.9N 允许转速 10,000r/min 环境温度范围 工作时:-10~+70℃ (90%RH以下) 保存时:-30~+85℃ (无结冰) 环境湿度范围 工作时、保存时:各90%RH以下 (无结露) 绝缘电阻 电容器接地,可除外 耐电压 电容器接地,可除外 振动 (耐久) 10~500Hz 100m/s 2或上下振 24V 0V GND 䕧ߎֵো ˄咥㡆˖AⳌǃⱑ㡆˖BⳌǃ㡆˖ZⳌ˅ 㪱㡆 ሣ㬑 㻤㡆 咥㡆ǃⱑ㡆ǃ㡆 E6H Џಲ䏃 OFF ON OFF ON OFF ON AⳌ BⳌ ZⳌ OFF ON OFF ON OFF ON AⳌ BⳌ ZⳌ 1/4T±1/8T˄90°±45°˅ T (360°) CWᮍ 1/4T±1/8T˄90°±45°˅ T (360°) CCWᮍ 䲚⬉ᵕᓔ䏃䕧ߎ ᮟ䕀ᮍ˖CW ˄Ң䕈ⱘᮍ...
E6H-CW6C 256P/R 请勿在超过额定环境要求的情况下使用。 ● 安装时 • 安装对象轴的尺寸为φ8 、长度请设为距安装面11mm以下 8mm以上。 • 安装对象轴容许位移请控制在径向0.05mm、轴向0.3mm以内。 • 安装面和安装轴的直角度请控制在0.03mm以内。 • 固定编码器时,请不要让板簧 (*部)受力。 • 固定旋转编码器时,用M3螺钉 (2根)把板簧固定在安装面上。 • 轴用中空轴上附属的带六角孔紧固螺丝固定。请以0.4N·m扭矩紧 固并用螺丝防松剂防松。 • 固定本体、布置导线时,请勿拉扯导线。请勿对本体及中空轴施 加冲击。 • 调整与要设置的装置的原点和编码器的Z相时,请务必一面确认 Z相输出一面安装编码器。 ● 连接时 电源接通时、切断时,可能会产生误脉冲,后续机种需要在电源接 通0.1秒后,切断0.1秒前使用。 另外,电源接通时,编码器电源接通后,再接通负载电源。