E6C2-CWZ5GH 360P/R
on NPN open-collector output PNP open-collector output Voltage output (NPN output) Line driver output*2
Output capacity
Applied voltage: 30 VDC max.
Sink current: 35 mA max.
Residual voltage: 0.4 V max.
(at sink current of 35 mA)
Applied voltage: 30 VDC max.
Source current: 35 mA max.
Residual voltage: 0.4 V max.
(at source current of 35 mA)
Output resistance: 2 kΩ
Output current: 20 mA max.
Residual voltage: 0.4 V max.
(at sink current of 20 mA)
AM26LS31 equivalent
Output voltage:
High level: IO = −20 mA
Low level: IS = 20 mA
Output voltage: VO = 2.5 V min.
VS = 0.5 V max.
Maximum response
frequency*3
100 kHz 50 kHz
料,玻璃码盘是在玻璃上沉积很薄的刻线,其热稳定性好,精度高,金属码盘直接以通和不通刻线,不易碎,但由于金属有一定的厚
相、B相的位相差90°±45° (1/4T±1/8T)
输出开始、
结束时间
1μs以下
(控制输出电压:5V负载电
阻1kΩ、导线长度:2m)
1μs以
E6C2-CWZ6C 2500P/R 的脉冲数越多,旋转槽圆盘的槽孔间隔越窄,越易受到振动的影响。在低速旋转或停止时,加在轴或本体上的振动使旋转槽圆盘抖动,可能会发生误脉冲。 (3)关于配线和连接 误配线,可能会损坏内部回路,故在配线时应充分注意: ① 配线应在电源OFF状态下进行,电源接通时,若输出线接触电源,则有时会损坏输出回路。 ② 若配线10, 20, 30, 40, 50, 60, 100, 200, 300, 360, 400, 500, 600, 720, 800, 1,000, 1,024, 1,200, 1,500, 1,800, 2,000 100, 200, 360, 500, 600, 1,000, 2,000 10, 20, 30, 40, 50, 60, 100, 200, 300, 360, 400, 500, 600, 720, 800, 1,000, 1,024, 1,200, 1,500, 1,800, 2,000 Output phases Phases A, B, and Z Phases A, A, B, B, Z, and Z Output configuration NPN open-collector output PNP open-collector output Voltage output (NPN output) Line driver output*2 Output capacity Applied voltage: 30 VDC max. Sink current: 35 mA max. Residual voltage: 0.4 V max. (at sink current of 35 mA) Applied voltage: 30 VDC max. Source current: 35 mA max. Residual...
E6C2-CWZ1X 400P/R 器的连接,应使用柔性连接器。在轴上装连接器时,不要硬压入。即使使用连接器,因安装不良,也有可能给轴加上比允许负荷还大的负荷,或造成拨芯现象,因此,要特别注意。 轴承寿命与使用条件有关,受轴承荷重的影响特别大。如轴承负荷比规定 矩 1 × 10-6kg·m2以下(600P/R以下为3 × 10-7kg·m2以下) 轴 负载 径向 50N 轴向 30N 允许转速 6,000r/min Operating: −10 to 70°C (with no icing), Storage: −25 to 85°C (with no icing) Ambient humidity range Operating/Storage: 35% to 85% (with no condensation) Insulation resistance 20 MΩ min. (at 500 VDC) between current-carrying parts and case Dielectric strength 500 VAC, 50/60 Hz for 1 min between current-carrying parts and case Vibration resistance Destruction: 10 to 500 Hz, 150 m/s 2 or 2-mm doub...