Products
产品

Heated Cement Resistors (JRX)
JRX 发热体水泥电阻器

Features
特点

1. Good heat-durability，low temperature coefficient, high overload power, good insulting performance.耐热性好，温度系数低，负荷功率大，绝缘性高。
2. Operating ambient temperature 使用环境温度 : -55°C ~ 275°C.
3. Insulating resistance value 绝缘电阻值: DC500V 1000 MΩ.
4. Insulating strength 绝缘强度: AC1500V/minute.
5. Resistance tolerance 阻值误差: ±5%, ±10%.

Test Item

Test Condition

Performance

Temperature Coefficient
温度系数

Test the resistance value at normal temperature and normal temperature added 100°C, calculate per °C resistance value change rate.
在常温及常温 100°C时分别测量电阻并计算每度的组织变化率。

±300ppm/°C

Short Time overload
短时间过负荷

According 10 times rated power to account the voltage or max. overload voltage(get the lower) for 5 seconds.
施以10倍额定电压或负荷电压（取较小者）5秒。

R≤±(2% R0 0.05Ω)

Resistance to soldering heat
耐湿性

Immerge into the 350±10°C tin stove for 2~3seconds
浸入350±10°C 锡炉中2~3秒钟。

R≤±(1% R0 0.05Ω)

Solderability
可焊性

Immerge into the 245±3°C tin stove for 2~3seconds
浸入245±3°C 锡炉中2~3秒钟。

The soldering area is over 95%. 锡焊面积超过95%。

Temperature cycling
温度循环

At -55°C for 30 min. ,then at 25°C for 10~15°C,then at 200°C for 30 min., then at 25°C for 10~15 min., total 5cycles.
在-55°C时放置30分钟，然后在 25°C放置10~15分钟，然后再 200°C时放置30分钟，接着在 25°C时放置10~15分钟。

R≤±(1% R0 0.05Ω)

Load life in humidity
耐湿负荷寿命

Overload rated voltage or Max. working voltage(get the lower) for 1000hours(1.5hours on and 0.5 hour off).at the 40℃±2℃ and 90~95% relative humidity.
在温度为40℃±2℃，相对湿度为90~95%的恒温恒湿箱中施加额定电压或工作电压（取较小者）共1000小时（通电1.5小时，断电0.5小时）。

R≤±(5% R0 0.05Ω)

Load life in heat
耐温负荷寿命

Overload rated voltage or Max. working voltage(get the lower) for 1000hours(1.5hours on and 0.5 hour off).at the 70℃±2℃. 在温度为70℃±2℃

R≤±(5% R0 0.05Ω)

Nonflammability
不燃性

Respectively load AC voltage by5,10,16times rated power for 5 minutes.
分别施以5,10，16倍额定功率加交流负荷5分钟。

No visible flame
不可有明显火焰

Note：The Power, Dimension and cable length can be according customer’s requirement to customize, the tolerance of each sect is ±5mm.
备注：我们可以根据客户要求定做功率，尺寸，以及长度。误差范围为±5mm。