dzsc/18/9315/18931547.jpg
| | BH、SDH、MSQ系列塑壳式电流互感器 BH、SDH、MSQ Molded-case current transformer | | 概述 Summary | BH、SDH、MSQ系列型电流互感器，供额定频率为50Hz，额定电压为0.66kV及以下的电力系统中作电流、电能测量和继电保护之用。
1、品种规格齐全，适用范围广，适用于一次电流为5A至5000A，1A至4000A的全部规格(包括非标规格)。二次电流有5A或1A两种，设计不同窗口种类可与任何汇流排及电缆对应使用。
2、外形设计美观、合理。
3、指标先进、国内，结构性能优良。
4、与国类产品相比，体积小、重量轻、容量大、精度高、符合电控设计紧凑化趋向的要求。
5、安全、阻燃、表面无一处带电，客体由进口阻燃材料高压注塑成型，强度高且不燃烧。
6、坚固、耐用、整个产品为全封闭型、有耐温、防潮、防振、防污、防盐雾、防窃电等特点。 | Series BH,MSQ,SDH current transformer is mainly used for power system with rated frequency 50Hz and rated voltage under 0.66KV to measure electric energy, current and protect relay.
1.With full complete of specification and wide range of application, suitable for any primary current range from 5A to 5000A or from 1A to 4000A(including non-standard specificaiton),the secondary current has two types:5A and 1A, the different window types can match with different bus-bars and cables.
2.With nice appearance and reasonable design.
3.With advanced technology and excellent performance.
4.Compared to same line of products, this product is more compact, less weight, larger capacity, higher accuracy and more compliance with the standard of electric-control design.
5.With feature such as safety, flame retardant, without static electricity in the surface, the case is made of imported flame retardant material by high-pressure casting, so it has feature of high strength and resisting flame.
6.With features of firmness, durability, full-seal , high temperature resistant, moisture proof, shock proof, anti-salt spray and prevent from electric-theft. | | | | 型号含义 Type designation | BH、MSQ、SDH本类型电流互感器特定型号：
L-电“流”互感器； K塑料外“壳”绝缘； M贯穿“母”线式； 1、2为设计序号
A/B分类；
1.A为方圆型，既可穿越电缆，也可穿越汇流排，一般作监控用。
2.B为卧式方孔型，可穿越1-3块汇流排，一般作监控用。
Model description for BH, MSQ and SDH current transformer :
L-current transformer; K-plastic case; M-bus type; 1 or 2-design S/N;
A/B classification:
1.A: for square or circular type, can go through cable or busbar, generally used for monitoring.
2.B: for horizontal square-hole type, can go through 1 to 3 busbar,generally used for monitoring. | | | | 使用范围 Application scope | 1.工作电压≤0.66kV;
2.额定频率50~60Hz;
3.海拔高度不超过1000m;
4.周围介质温度为-5℃~ 40℃
5.空气相对温度不超过85%;
6.用于没有雨雪直接侵袭，无严重污染，无爆炸无剧烈震动、无腐蚀金属和破坏绝缘额尘埃或蒸汽的场所。
1.working voltage: ≤0.66kV;
2.rated frequency: 50~60Hz
3.altitude≤1000m;
4.amboent temperature: -5℃~ 40℃
5.RH: ≤85%;
6.environment without rain or snow, no heavy pollutat, no explpsion or shock, no corrosive metal or dust or steam. | | | | 使用方法 Usage | 1.根据一次电流及母线截面等参数选取对应的规格。一次导线（一次线圈）穿越CT窗孔，卸下CT顶部接线罩壳，支掉引线垫片，二次线引出后罩壳复位，计量电能用的可利用固定螺丝和罩壳上小孔加封铅印，以防窃电。
2.产品极性表示，P1表示一次线圈的极性端，S1表示P1的同名端，S2表示P2的同名端。
1. Select the suitable specification according to primary current and section of bus. The primary windings go through the window-hple of CT, dismantle the cover on the top of CT and remove shim, the cover will reture to its original position after the secondary windings lead out, use screw to fix it and seal with lead inside the hole of case to prevent from electric-theft.
2.Polarity: P1 indicates the ploarity of primary winding. S1 indicates the same polartiy of P1, S2 indicated the same polarity of P2. | | | | 注意事项 Note | 1.互感器允许接到不超过0.66kV的交流电路中，长期工作电流不超过额定值的1.1倍，允许1.2倍额定电流的短时间使用，背景时间不超过1小时，瞬时（1S内）工作电流不允许超过60倍额定电流（30B型为40倍）非标和作保护用的例外。
2.测试仪表接于S1，S2端子上，此时必须注意所接仪表的总阻抗（包括接线）不超过互感器的额定负荷。
3.互感器在运行中严禁二次开路，加入二次线圈以外在通电时发生开路，则必须进行退磁处理，以减少误差的增加。
1. The transformer is used for AC circuit with rated voltage under 0.66KV, the working current should not exceed 1.1 times of rated current in long-term use of this product; for short-time use(e.g., Beijing time less than 1 hour), the working current is permitted up to 1.2 times of rated current, the instantaneous(within ls)working current should not exceed 60 times of rated current (model 30B shall be 40 times of that)(excluding non-standard or any type use for protection)
2.The measuring meter should beconnected to terminal S1 and S2, and the overall impedance of the transformer(including connecting wire) should not exceed the rated load of transformet.
3.The secondary winding is strictly prevented secondary from open circuit during operation, If any open ciruit occars accidentally for secondary winding, it musted be treat with demagnetizing process to reduce error during measurement. | | | | BH型安装方法 BH installment method | | dzsc/18/9315/18931547.jpg | | | | BH型窗口尺寸 Window size for model BH | | dzsc/18/9315/18931547.jpg |
乐清市长城控制电器厂成立于1991年，是一家以高、低压电气成套设备，高、低压电器的制造、销售和电子商务为主导，集科研、生产、贸易为一体的无区域性的公司.
公司生产各类断路器,接触器,继电器,断路器,漏电断路器,高压真空断路器，高压真空接触器及代理各类进口品牌电器.
公司多年秉着科技创新，质量的原则，多年以来先后为香港施耐德集团，中国人民集团，上海人民企业集团，上海德力西实业有限公司，上海中力集团，民扬集团，中国龙光集团，上海一洲集团，上海中科集团，上海三洲集团提供优质的OEM服务。
公司将坚持“以人为本，科技创新，质量”的经营理念，加快实现管理现代化、产品智能化和经营国际化步伐，继往开来，追求卓越，以一流的质量、一流的品牌、一流的技术、一流的服务、一流的业绩回馈社会！
主要产品型号有CJX2,CJX1,CJ12,CJX4,CJX5,CJX7,CJX8,CJ20,CJ40,CK1,CKJ5,VS1,DZ20Y,RMM1,RMW1,RMC1,CM1,CH1,CW1,HSW1,GSW1,DZ47,C65,NSE,LC1,ME,DW45,DW15,DW17,MY4NJ,M2NJ,GV2,DZ108.3VE1,ST3P,B交流,A交流,CXK-M,XCK-P,watsna等。
- 所属城市：浙江 温州
- [联系时请说明来自维库仪器仪表网]
- 联系人： 郑晓凯
- 电话：
- 传真：
- 手机：13506675629
- QQ ：
|
|
