让卖家找上门
发布询价>>
您所在的位置:仪器仪表网> 电子元器件>供应LED大功率模块

供应LED大功率模块

价 格: 面议
是否提供加工定制:
种类:LED模组
型号/规格:KP100W3434CS100
品牌/商标:科纳
显示颜色:单色
显示方式:静态显示
像素直径:46*42(mm)
像素间距:46*42(mm)
模组尺寸:46*42(mm)
屏幕尺寸:46*42(英寸)
亮度:超高亮
灰度:正常
像素:常规
分辨率:10

深圳市科纳实业有限公司
ShenZhen Kena Industry Co.,LTD
产品规格
Production Specification
承 认 书
Samples approval sheet
客户名称(Customer name):
元件名称(Production name):
型 号(Model): KP100W3434CS100
编号(Part number): 2010030307-KN
日期(Date): 2010-3-3
深圳市科纳公司
KENA INDUSTRY CO.,LTD
编制
Prepared by
审核
Checked by
核准
Approved by
市场部
Market Dept.
李小姣
客户确认
CUSTOMER CONFIRMATION
确认
Confirmed by
审核
Checked by
核准
Approved by
地址:深圳市宝安区公明镇合水口村下朗工业区第 10 栋
Address:Building 10.Xialang Industry zone, HeShuiKou, GongMing town, BaoAn district, Shenzhen city.
电话(Tel):0755-27168881、27168889、27168080、27168086、27168860
传真(Fax):0755-27168989
网址(Net address):www.knled.com
邮箱(E-mail):szsyl@szonline.net、kena@knled.com
深圳市科纳实业有限公司
ShenZhen Kena Industry Co.,LTD
产品规格
Production Specification
型 号 Model : KP100W3434CS100 页码 Page: 1/5
一、 外形图Outline dimensions:
-

单位
Unit
公差
Tolerance
芯片材料
Die material
胶体颜色
Lens color
发光颜色
Emission color
mm ±0.2mm InGaN Water Clear White
※备注:承认书之编号和型号可用于查询,客户如有需要,请提供相应的编号和型号。
Remark:P/N & Model in samples approval sheet can be used to inquire,please provide corresponding P/N& model if
customer need .
深圳市科纳实业有限公司
ShenZhen Kena Industry Co.,LTD
产品规格
Production Specification
型 号 Model : KP100W3434CS100 页码 Page:2/5
二、光电参数Photoelectricity Parameter
(环境温度Ambient temperature:25℃ 湿度humidity:RH60%)
项目
Item
符号
Symbol
测试条件
Test condition
最小值
Min
典型值
Type

Max
单位
Unit
正向电压
Forward voltage
VF IF=2800mA -- 34 -- V
反向电流
Reverse current
IR VR=5V -- -- 10 μA
光通量(Light) φ IF=2800mA 7000 8000 -- Lm
色温
Color temperature
CCT IF=2800mA 5500 -- 6500 K
光谱半宽度
Spectrum line half width
Δλ IF=2800mA -- -- -- nm
静电解除极限
ESD Withstand limit
ESD
(HBM)
-- -- -- -- V
备注:
1、亮度测试公差±15%、波长测试公差±1nm、正向电压测试公差±0.05V
The tolerance of intensity:±15%, The tolerance of wave length:±1nm,The tolerance of forwards voltage: ±0.05V.
Only reference for above data when testing.
2、以上数据是在良好散热的情况下测试的
The datum in measured under excellent dispelling heat.
三、极限参数Absolute Maximum Rating
(环境温度Ambient temperature:25℃ 湿度humidity:RH60%)
项 目
Item
符号
Symbol
数值
Value
单位
Unit
备注
Remark
正向电流
Forward Current IF 2800 mA ---
正向峰值电流
Peck forward current
IFM 4480 mA F=1KHZ,占空比(duty cycle)1/10
反向耐压
Reverse Voltage
VRP 5 V ---
耗散功率
Power Dissipation
Pm 100 W ---
工作环境温度Operation
temperature
Tamb -40 至 60 ℃ ---
贮藏温度
Storage temperature
Tstg -40 至 100 ℃ ---
深圳市科纳实业有限公司
ShenZhen Kena Industry Co.,LTD
产品规格
Production Specification
型 号 Model : KP100W3434CS100 页码 Page: 3/5
四、典型光电特性曲线图Typical photoelectricity characteristic curve chart
Forward Current(mA)
4300
3800
Relative Iuminous Intensity
Ambient Temperature TA(℃)
-20
0
1000
2000
3000
4000
Relative Luminous Intensity VS
Ambient Temperature
0 20 40 60 80
Relative Luminous Intensity VS
Forward Current
Forward Voltage(V)
16 22 28 34 40 46
0
2300
2800
3300
Forward Current VS
Forward Voltage
Relative Luminous Intensity
2500
2000
1500
1000
500
0
0 400 800 1200
Forward Current(mA)
Ambient Temperature TA(℃)
0 20
500
1500
2500
3500
4500
Allowable Forward
Current(mA)
Allowable Forward Current VS
Ambient Temperature
40 60 80 100
1400 1600
5000
深圳市科纳实业有限公司
ShenZhen Kena Industry Co.,LTD
产品规格
Production Specification
型 号 Model : KP100W3434CS100 页码 Page: 4/5
五、可靠性实验项目 Reliability Test Project
描述
Description
项目
Item
测试标准
Test criterion
测试条件
Test condition
测试时间
Test time
数量
Qty
失效数量
Fail qty
寿命测试
Life test
常温寿命测试
Life test(room temperature) JIS7021:B4 Ta=25℃±5℃,IF=2800mA 1000Hrs 22 0
高温存储
High temperature store
JIS7021:B10
MIL-STD-202:210A
MIL-STD-750:2031
Ta=60℃±5℃ 1000Hrs 22 0
低温存储
Low temperature store JIS7021:B12 Ta= -35℃±5℃ 1000Hrs 22 0
高温高湿测试
High temperature/ humidity test
JIS7021:B11
MIL-STD-202:103D
Ta=80℃±5℃
RH=85%
1000Hrs 22 0
冷热冲击测试
Cold / Heat strike test
JIS7021::B4
MIL-STD-202:107D
MIL-STD-750:1026
5min
-30℃±5℃←→100℃±5℃
5min 5min
50Cycles 22 0
环境测试
Ambience
test
冷热循环测试
Cold and heat cycle test
JIS7021:A3
MIL-STD-202:107D
MIL-STD-705:105E
30min 30min 30min
-35℃~25℃~85℃~25℃
30min 5min 30min 5min
50Cycles 22 0
判断标准Judging criterion:
判断标准
项目Criteria
Item
符号
Symbol
实验条件
Experiment condition
Min. Max.
Forward Voltage VF IF=2800mA ---- Initial Datex1.1
Reverse Current IR VR=5V ---- 50μA
Luminous Intensity IV IF=2800mA Initial Datex0.8 ----
深圳市科纳实业有限公司
ShenZhen Kena Industry Co.,LTD
产品规格
Production Specification
型 号 Model : KP100W3434CS100 页码 Page: 5/5
六、注意事项 Note
(1)防静电措施ESD countermeasure
静电及高压会对LED 造成损坏,特别是晶片材质为InGaN 的产品对静电防护要求更加严格,要求在使用和检验
产品时戴防静电手腕带或防静电手套,焊接工具及设备外壳需可靠接地,焊接条件遵循此份规格书中的条件。
Static electricity and high volt can damage led,The production whose Die material is InGaN must strictly required
to prevent ESD,Must put on static glove and static fillet,Soldering tool and the cover of device must connect the
ground,soldering condition follows the related stating of production specification manual。
(2)过电流保护Protecting countermeasure when over current
为避免由于电压的变化引起大电流冲击而造成产品损坏,需要加入保护电阻。
Need add the protecting resistor in circuit in order to avoid damaging led due to big current and voltage fluctuation。
(3)LED 安装方法LED installation method
1、在应用中必须将大功率安装在适当的散热片上,在散热片和大功率之间打上散热膏。
When using it ,should smear silicon glue on the back of power LED and install it on a proper heatsink .
2、注意在拿、放和安装、使用大功率时,不能给大功率上的芯片区施加任何压力,防止里面金线开路。
Don’t press the wafer area of power LED in case of the gold wire open ,When touching the production.
(4)存储时间Storage time
1、在温度5℃~35℃,湿度RH60%条件下,产品可保存一年。超过保存期的产品需重新检测后方能使用。
Led can be stored for a year under the condition: the temperature of 5℃~35℃ and humidity of RH60%,These
production must be re-inspected and tested before use if their storage time exceed a year。
2、如果打开的产品在5℃~35℃,RH60%的空气条件下放置超过一周,则需要将产品在65℃±5℃的环境中放置
24 小时以上,并尽量在十五天内使用。
If led is exposed in air for a week under the condition: the temperature of 5℃~35℃,humidity of RH60%,must
place the led in the ambience of 65℃±5℃ for 24 hours and use it in 15 days for best。
(5)清洗Cleaning
当用化学用品清洗胶体时必须特别小心,因为有些化学品对胶体表面有损伤并引起褪色如三氯乙烯、丙酮等。
可用乙醇擦拭、浸渍,时间在常温下不超过3 分钟。
Be careful of some chemical results in the led colloid fades and damage when using chemical clean the led,such as
chloroethylene, acetone etc。 can use ethanol to wash or soak led but the time don’t exceed 3 minutes.
(6)对分光产品,请按分包使用,避免出现色差及灯暗
For the LED sorted light,please sort the different package to use and cann’t mix them in case of dark light and color
error.

深圳市科纳实业有限公司
公司信息未核实
  • 所属城市:广东
  • [联系时请说明来自维库仪器仪表网]
  • 联系人: 夏时
  • 电话:86075527642115
  • 传真:86075527642016
  • 手机:13392830325
  • QQ :
公司相关产品

供应LED2*5*8方形有帽沿系列

信息内容:

2.0*5.25*8.0mm Rectangle with Flange LED Lamps(2.0*5.25*8.0毫米 方形有帽沿发光二极管) Package Dimensions (mm)封装尺寸图(毫米) Part Number产品型号Chip Material芯片材质Lens Type外观颜色Emitting Color发光颜色Forward Voltage顺向电压(V)Dominant Wavelength主波长(nm)Luminous Intensity 发光强度(mcd)Reverse Current反向电流(μA)Viewing Angel视角(deg)TYP典型值MAX值MIN最小值MAX值MIN最小值MAX值MAX最小值△θ半功率角KSBM25804W3-8InGaNWater Clear水色透明S-B Pure-Blue超高亮纯蓝色3.303.8046047030040010100KHBM25804DB-8InGaNBlue Diffused蓝色扩散S-B Pure-Blue超高亮纯蓝色3.303.804604706011010135KSGM25804W5-8InGaNWater Clear水色透明S-B Pure-Green超高亮纯绿色3.303.8052053050060010100KNGL25804DG-8GaPGreen Diffused绿色扩散N-B Yellow Green普亮黄绿色1.952.505605706910135KSWW25804W3-8InGaNWater Clear水色透明S-B Pure-White超高亮白色3.303.80//30050010100KSWW25804W5-8InGaNWater Clear水色透明S-B Pure-White超高亮白色3.303.80//50080010100KSRS25804W3-8AlGaInPWater Clear水色透明S-B Orange Red超高亮...

详细内容>>

3W大功率LED绿色 3w大功率led led大功率 led 3w 集成大功率led

信息内容:

3W大功率LED绿色Electrical/Optical Characteristics At Ta=25℃室温下电气特性测试参数 Part Number产品型号Emitting Color发光颜色Forward Current(mA)顺向电流Power Dissipation(W)耗散功率Wavelength(nm) TC(K)波长及色温Drive Voltage(V)顺向电压LuminousFlux(lm)光通量HN-P03R1430380RED红色12003.06202.075Min822-6262.2-2.685Avg6302.8105MaxHN-P03Y2430380YELLOW黄色12003.05852.075Min589-5922.2-2.685Avg5952.8105MaxHN-P03B3430340BLUE蓝色10003.454603.230Min464-4673.4-3.745Avg4704.060MaxHN-P03G6430380GREE绿色10003.455203.275Min522-5253.4-3.785Avg5304.0100MaxHN-P03W64103100WHITE白色7502.860003.2100Min65003.4-3.6120Avg70003.8140MaxHN-P03W3410380WHITE暧白色7502.827003.270Min30003.4-3.685Avg33003.8100Max Absolute Maximum Ratings At Ta=25室温时的使用特性参数 Parameter参数类别Red/Yellow红/黄光系列Blue/Gree/White蓝/绿/白光系列Viewing Angle发光角度125±5125±5Peak Pulsed Forward Current(mA)1/10s瞬间冲击电流极限值20002000Reverse Voltage(V)反向崩溃电压≥8≥5Reverse Current(uA)反向漏电电流≤30≤...

详细内容>>

相关产品