FWTS902Z

3.5K/REEL

LED White Angle,4014size

只销售全新原装进口货

电话确认当天价格

ADD:深圳市福田区福虹路华强花园Ｃ座１３Ｃ

TEL：0755-82813795陈’s 

13570861289

QQ：492820236(实单供图片)

FAX：0755-82813792

使用注意事项

(1) Storage（1）储存

In order to avoid the absorption of moisture, it is recommended to store in the dry box (or desiccator)为了避免水分吸收，建议储存在干燥框（或干燥）

with a desiccant.用干燥剂。Otherwise, to store them in the following environment is recommended.否则，储存环境，他们在下面的建议。

Temperature : 5℃3℃温度：5℃3℃

Humidity : 60%HR max.湿度：60％心跳率。

(2) Attention after opened（2）打开后注意事项

However LED is corresponded SMD, when LED be soldered dip, interfacial separation may affect the然而LED是对应贴片，当LED被浸焊，界面分离，可能会影响

light transmission efficiency, causing the light intensity to drop.光传输效率，使光的强度下降。Attention in followed.注意在遵守。

a.答：After opened and mounted, the soldering shall be quickly.打开后，安装，焊接，应迅速。

b.湾Keeping of a fraction保持的一小部分

Temperature : 5 40℃温度：40℃5

Humidity : less than 30%湿度：小于30％

(3) In case of more than 1 week passed after opening or change color of indicator on desiccant（3）在干燥剂外壳颜色变化的指标就超过1星期或打开后通过

components shall be dried 10-12hr.组件应干燥10 - 12hr。at 60±5℃.在60 ± 5℃。

(4) In case of supposed the components is humid, shall be dried dip-solder just before.（4）在部分案件应该是潮湿的，应干浸焊前。

100Hr at 80±5℃ or 12Hr at 100±5℃.100小时，在80 ± 5℃或12Hr在100 ± 5℃。

(5) Any mechanical force or any excess vibration shall not be accepted to apply during cooling process to（5）任何武力或任何多余的机械振动，不得接受申请在冷却过程

normal temp.正常温度。after soldering.焊接后。

(6) Quick cooling shall not be avoid.（6）快速冷却，不得回避。

(7) Components shall not be mounted on warped direction of PCB.（7）成分，不得安装在印刷电路板翘曲的方向。

(8) Anti radioactive ray design is not considered for the products listed here in.（8）抗放射性射线的设计是不考虑上市的产品在这里英寸

(9) Gallium arsenide is used in some of the products listed in this publication.（9）镓砷化物用于出版一些这家上市的产品。These products are这些产品

dangerous if they are burned or smashed in the process of disposal.危险的，如果他们被烧毁或处置瓦解的过程。It is also dangerous to drink the这也是危险的喝

liquid or inhale the gas generated by such products when chemically disposed.液体或吸入化学处理这类产品时产生的气体。

(10) This device should not be used in any type of fluid such as water, oil, organic solvent and etc. When（10）本设备不得用于任何类型的液体，例如水，油，有机溶剂等当

washing is required, IPA should be used.需要清洗，应使用国际音标。

(11) When the LEDs are illuminating, operating current should be decided after considering the ambient（11）当LED是照明，工作电流应考虑后决定的环境

maximum temperature.温度。

(12) LEDs must be stored to maintain a clean atmosphere.（12）LED的必须存放，保持清洁的气氛。If the LEDs are stored for 3 months or more如果LED存储3个月或以上

after being shipped from SSC, a sealed container with a nitrogen atmosphere should be used for storage.运到后，气氛南南合作，氮气密封容器应使用与储存。

(13) The LEDs must be soldered within seven days after opening the moisture-proof packing.（13）LED的焊接必须在7天之后打开防潮包装。

(14) Repack unused products with anti-moisture packing, fold to close any opening and then store in a dry（14）未使用的产品重新包装任何开放与防潮包装，折叠关闭，然后存放在干燥

place.地方。

(15) The appearance and specifications of the product may be modified for improvement without notice.（15）外观和产品规格的通知，可修改为无改善。