供应气体分析仪

价格：

76.00

详细介绍
企业详情

品牌:银月型号:6900 测量范围:标准（MPa）适用介质:标准额定出口压力:标准（MPa）额定流量:标准（m3/h）用途:氧气减压器结构:单级式工作原理:正作用式环境温度:130（℃）装箱数:标准

APPLICATION

The Model 6900 is designed for the measurement of gas mixtures produced in the industrial gas industry. The analyzer is designed to quickly (3 - 5 minutes) analyze a gas cylinder, without the use of calibration standards, wet chemicals, or special knowledge of gas analysis instrumentation. The analyzer is designed so that it may be used directly in the cylinder-filling environment.

The analyzer may also be used to check gas-mixing systems in the field. If desired. The analyzer may be run continuously as an on-stream analyzer. A linear 4-20 mA output is available on all ranges.

The analyzer use's Thermco's patented thermal conductivity detector/microprocessor technology to directly readout numerous mixtures created for the welding, heat treating, and food packaging industries.

The analyzer contains 9 ranges, which are selected with the push buttons on the front of the analyzer. All 9 ranges are factories calibrated. A custom ranges for calibration by the user us also available.

SPECIFICATIONS

RANGES

0-100% Carbon Dioxide in Argon
0-100% Oxygen in Argon
0-100% Helium in Argon
0-100% Hydrogen in Argon
0-100% Nitrogen in Argon
0-100% Carbon Dioxide in Nitrogen
0-100% Helium in Nitrogen
0-100% Hydrogen in Nitrogen
Custom Range

ACCURACY

Valid over 50º F to 90º F(10ºC to 32ºC) ambient temperature conditions.

±0.3% of minor component over range of 0-10.1%, all ranges.
Example:for a 5% O₂in Ar mixture, the analysis will be between 4.7 and 5.3% O₂.

±0.5% of minor component over a range of 10.1 % to 30.0%, all ranges.
Example:for a 25% CO₂in N₂mixture, the analysis will be between 24.5 % and 25.5 % CO₂.

±2% of minor component over a range of 60.1% to 100.0%, all ranges, except CO₂in Ar, which has an accuracy of ±8%. Example: for a 75% He in Ar mixture, the analysis will be between 73.0% and 77.0% He.

MINIMUM/MAXIMUM OPERATING TEMP.

40ºFto 100ºF (4ºC to 38ºC)

RESOLUTION

0.1%

RESPONSE TIME

95% in 45 sec. for typical gas mixtures

UTILITIES REQUIRED

Reference Gas: Commercial grade argon or nitrogen (depending upon the base gas range used) is required to flow continuously at 0.5 SCFH during analysis.

Sample Gas: Moisture and oil free sample gas is required to flow continuously at 1.0 SCFH during analysis.

Sample, reference gas pressure: 1-100 PSIG

Power: 115 VAC, 60Hz , 1 Amp (220 VAC, 50/60 Hz. Optional)

FREQUENCY OF CALIBRATION

Calibration is recommended once a year when used under spot-checking conditions; if run continuously will depend on conditions and range.

WARM UP TIME

8 minutes under room temperature conditions

PHYSICAL SPECIFICATIONS

Size: 9". high, 11". wide, 14". deep (23 cm X 28 cm X 35.5 cm),
Weight: 22 pounds (10 kg)

ALTITUDE

Sea level to 2000 ft. (Altitude above 2000 ft. will cause some inaccuracy; consult the factory)

ANALYZER OUTPUTS

Current: 4-20 mA, proportional to gas analysis range selected (available on all ranges). The 4-20 mA resolution equals display resolution of 0.1% gas analysis.

COMMON MIXTURES MEASURED
RANGE	MIXTURE EXAMPLE	APPLICATION
0-100% CO₂in Ar	5% CO₂in Ar 25% CO₂in Ar	MIG shield gas
0-100% O₂in Argon	5% O₂in Ar	MIG shield gas
0-100% He in Ar	25% He in Ar	MIG, TIG shield gas
0-100% He in Ar	75% He in Ar	MIG Shield gas
0-100% H₂in Ar	5% H₂in Ar 35% H₂in Ar	Plasma Cutting, Welding
0-100% N₂in Ar	10% N₂in Ar	Lamp Filling
0-100% CO₂in N₂	30% CO₂in N₂	Food Packaging
0-100% O₂in N₂	5% O₂in N₂	Special Atmosphere
0-100% He in N₂	10% He in N₂	Leak Detection
0-100% H₂in N₂	10% H₂in N₂ 75% H₂in N₂	Furnace Atmosphere

PRINCIPLES OF OPERATION

Each gas has the ability to conduct heat at a specific rate. This is known as the thermal conductivity of the gas. This property is utilized in the Thermco thermal conductivity detector. Heated metal filaments are exposed to the zero and sample gases. The amount of heat carried away by the gas changes the rate of cooling of the wire filament and therefore, its temperature change. This temperature change causes a resistance change. Since the filaments are arranged in a Wheatstone bridge, the resistance change can be converted to an electrical current that is read out on a meter.

Traditionally, a drawback to using the thermal conductivity method has been the non-linear signal created from virtually all-binary gas mixtures. The user had to refer to a curve in order correct for the non-linearity. The model 6900 is a significant improvement in the technology of handling the signal from the thermal conductivity detector. The unique curves generated by the 9 binary gas pairs are each programmed at the factory into the microprocessor in the Model 6900. The user selects the range of interest from the front panel of the analyzer is able to read out directly in the percent gas analysis for that particular gas mixture.

The calibration stability of the model 6900 analyzer is exceptional, especially compared to the infrared type or chemical cell type gas analyzers which may require recalibrations on a daily basis. It is recommended that the calibration be checked once per year, if used on a spot checking basis.

CUSTOM RANGE

The user may encounter a gas mixture pair other than the nine standard ranges built into the analyzer. In this case, the user may perform an analysis by inputting his own calibration data into the analyzer. This can be accomplished by utilizing the push buttons on the front meter. Guidance is available from the factory concerning the thermal conductivity response of a wide variety of gas pairs.

3 GAS MIXTURES

Although the Model 6900 is not normally intended to measure a 3-part mixture, mixtures of Ar / CO₂/ O₂may be approximately measured if the user knows the oxygen level in the mix. Contact Thermco for details.

SERVICE

Thermco has been providing service for their analyzers since 1951. The Thermco repair department can normally complete repairs in two weeks.

NOTICE

The Model 6900 is not intended to measure oxygen/nitrogen mixtures for breathing air, oxygen purity, or other medical applications.

The Model 6900 is not designed to be used with toxic gases or gases corrosive to brass or nylon.

ACCESSORIES SUPPLIED

Along with the analyzer are supplied two 10 ft. lengths of tubing to run from the ports on the Model 6900 to cylinder regulators.

ORDERING INFORMATION

Orders may be placed through many local industrial gas suppliers. Orders may also be placed directly with the Thermco factory.

In the interest of continued product improvement, Thermco reserves the right to change design features without prior notice.

Sale of this equipment is under the terms of the Thermco warranty available on request.

高纯气路安装能手(及其他流通管道)------“苏州银月气路控制系统有限公司”为您提供气路系统的全面的设计和安装。网址: www.yy-gasway.com 邮箱:hobeer@163.com. 本公司引进全球‘德国全自动管管焊接设备’及的技术工程人员，为半导体,医药,光伏制造等洁净管道提供安装服务. 我们紧跟全球实验室先进技术及先进设计思想，为您的实验室量身打造出一流的气路系统，满足实验员全方位的安全快捷用气要求。气路系统在当今先进科学技术中有举足轻重的应用，其中尤以冶金技术﹑机械加工﹑表面处理为至关重要的技术，其中融汇有气体动力学﹑工程美学等学科的精华。洁净是气体追求，洁净气体又是仪器分析得出精确结果的前提和有效保障，我们力求气体在输送过程中物质不变性，优质的材料和科学的加工工艺是制造合格的气路管道组件的关键。随着现代制造技术的提升气路还将得到迅猛的发展。我公司和国内外高端制造商合作，代理一批品牌产品，包括:钢管﹑阀门接头组件﹑汇流排﹑减压器﹑配比器；气体发生器﹑真空泵﹑压力表等。代理品牌有：TESCOM﹑ROTAREX﹑PARKER﹑GENTEC﹑AMFLO﹑TUFF﹑WIKA；电磁阀有ASCO﹑BURKERT；气体发生器和真空泵有PAKER﹑ILMVAC， Etc.美国配比器THERMCO，汇流排 CONCOA，产品含盖EP级﹑BA级高纯净管道的需求，广泛应用于半导体制造﹑医药﹑电子﹑材料﹑造纸﹑食品﹑能源等实验分析的过程控制。中国苏州，吸引着全球投资者的目光，这里是开拓者的战场，成功者的乐园。我们曾经为你们服务，现在还会一如既往的为你们服务！银月气路全体员工热诚欢迎你们的到来! 谢谢！美国捷锐企业(上海)有限公司 GENTEC品牌苏州特约经销商; 美国艾默生过程控制有限公司 TESCOM品牌苏州特约经销商。重点气路工程例举： 1. 苏州市环境监测中心站 2. 中国科学院苏州纳米技术研究所 3. 波林化工（常州）有限公司意ITALY Polynt Chemical (Changzhou) Co., Ltd. 4. 太仓市农产品检测中心 5. 张家港沙钢集团测试中心 6. 中粮集团安徽宿州化工有限公司 7. 浙江省淡水水产研究所 8. 贝克休斯(苏州)油田设备制造有限公司美U.S.A Baker Hughes(Suzhou) Oilfield Equipment Manufacturing 9. 山东金岭集团有限公司 10. 马斯特模具(昆山)有限公司加CANADA Mold　Masters 11. 上海西门子开关有限公司德GERMAN ShangHai Siemens 12. 奥加诺(苏州)水处理有限公司日本JAPAN ORGANO(SUZHOU) WATER TREATMENT CO.,LTD 13. 威友光电(苏州)有限公司 www.wellypowerop.com.cn 14. 太仓市检验检疫局技术中心

苏州银月气路控制系统有限公司

公司信息未核实