特点:
Current-Mode Type PWM Control
Built-in Random Switching Function
The function reduces the EMI noise and enables a simplified (low-cost) EMI filter,
by the slight- random-change of PMW frequency fOSC.
Auto-Standby Function: The burst-oscillation enables the low standby power. Input Power PIN < 25mW at no load
Built-in Startup Circuit, enabling low power consumption
Brown-In / Brown-Out Function
The function enables the oscillation start/stop by externally rated input voltage and makes protections at low input
voltage.
Overcurrent Protection (OCP) with Built-in Input Compensation Circuit:
The protection has less AC input voltage dependency.
Overload Protection (OLP) with Built-in Delay Timer
High Speed Latch Release Function
The function releases the latch immediately at AC supply OFF, after the latch protection operation.
Bias-Assist Function, reducing Operating VCC voltage drop
The function improves the startup operation and makes a low VCC capacitor applicable.
Leading Edge Blanking Function
Slope Compensation Function
Built-in Avalanche Energy Guaranteed High-Voltage Power MOSFET
Various Protections
Overcurrent Protection (OCP)--------------------------------- Pulse-by-Pulse
Overload Protection (OLP) ------------------------------------ Auto-Restart
Overvoltage Protection (OVP) -------------------------------- Latch Shutdown
Thermal Shutdown Protection (TSD) ------------------------ Latch Shutdown
产品糸列Product Lineup:
dzsc/18/2300/18230076.jpg
典型应用电路Typical Application Circuit:
dzsc/18/2300/18230076.jpg
LCTA28CE系列立式穿芯微型精密电流变换器 一、 特 点: 1、立式穿芯印刷线路板直接焊接安装、外形美观; 2、体积小,精度高;全封闭,机械和耐环境性能好,电压隔离能力强,安全可靠。 二、使用环境条件: 1、环境温度:-40℃~+85℃; 2、相对湿度:温度为40℃时不大于90%。 三、工作频率范围:20Hz~20KHz。四、绝缘耐热等级:B级(130℃)。五、安全特性: 1、绝缘电阻:常态时大于1000MΩ; 2、抗电强度:可承受工频6000V/1分钟; 3、阻 燃 性:符合UL94-Vo级。 六、外形图、安装尺寸和线圈图: dzsc/18/2300/18230077.jpg 七、性能参数: 1、 用电阻法直接获得采样电压时(如下图一所示),性能参数见表一; 2、 用IC法获得采样电压时(如下图二所示),性能参数见表二; dzsc/18/2300/18230077.jpg 表 dzsc/18/2300/18230077.jpg
LCTA23CE系列立式穿芯微型精密电流变换器 一、 特 点: 1、立式穿芯印刷线路板直接焊接安装、外形美观; 2、体积小,精度高;全封闭,机械和耐环境性能好,电压隔离能力强,安全可靠。 二、使用环境条件: 1、环境温度:-40℃~+85℃; 2、相对湿度:温度为40℃时不大于90%。 三、工作频率范围:20Hz~20KHz。 四、绝缘耐热等级:B级(130℃)。 五、安全特性: 1、绝缘电阻:常态时大于1000MΩ; 2、抗电强度:可承受工频6000V/1分钟; 3、阻 燃 性:符合UL94-Vo级。 六、外形图、安装尺寸和线圈图: dzsc/18/2300/18230078.jpg 七、性能参数: 1、 用电阻法直接获得采样电压时(如下图一所示),性能参数见表一; 2、 用IC法获得采样电压时(如下图二所示),性能参数见表二; dzsc/18/2300/18230078.jpg 表一: dzsc/18/2300/18230078.jpg 表二: dzsc/18/2300/18230078.jpg 八、注意事项: 1.电流变换器初级应串联于被测电流回路中,次级应近似工作于短路状态。 2.电流变换器次级电路不允许开路,所以请不要装熔断器。