供应PT6103 -线性锂电池充电管理芯片
| 价 格： | 面议 | |
| 型号/规格： | PT6103 | |
| 品牌/商标： | 上海华润矽威 |
The PT6103 is a highly integrated Li-ion battery linear charging management device targeted at space limited portable applications. The PT6103 offers an integrated MOSFET and current sensor, reverse blocking protection, high accuracy current and voltage regulation, charge status indication, and charge termination in SOT23,DFN6,DFN8 or ESOP8 package. The PT6103 charges a battery in three phases: trickle charging, constant current and constant voltage. No blocking diode is required due to the internal MOSFET architecture. The thermal feedback regulates the charging current to limit the chip temperature during high power operation or high ambient temperature to maximize the charge rate without risk of overheating . The charge voltage is fixed at 4.2V, and the charge current can be programmed externally with a single resistor. The PT6103 automatically terminates the charge cycle when the charge current drops to 1/10 the programmed value after the final float voltage is reached. Once the temperature outside the normal range thresholds is detected the PT6103 immediately stops the charging and CHG pin output 10Hz square wave. And charging is stopped until restart the chip again. And when the TS pin is floating or connected to ground, the battery temperature protection is disabled. FEATURES l Charges Single Cell Li-Ion Batteries Directly from USB Port l Programmable Charge Current Up to 800mA l No MOSFET, Sense Resistor or Blocking Diode Required l Complete Linear Charger in SOT23-6, DFN6, DFN8 or ESOP8 Package for Single Cell Lithium-Ion Batteries l Battery Thermal Protection l Constant-Current/Constant-Voltage Operation with Thermal Regulation to Maximize Charge Rate Without Risk of Overheating l Preset 4.2V Charge Voltage with ±1% Accuracy APPLICATIONS l Cellular Telephones, PDAs, MP3 Players l Bluetooth Applications l Digital Cameras l Charging Docks and Cradles
TYPICAL APPLICATION CIRCUIT TYPIC dzsc/18/2062/18206280.jpg
- 所属城市：广东 深圳
- [联系时请说明来自维库仪器仪表网]
- 联系人： 郑先生
- 电话：0755-82570180
- 传真：0755-82570180
- 手机：18948314942
- QQ ：
供应基于PT2202的24W AC-DC开关电源
信息内容：PT2202 Current Mode PWM Controller GENERAL DESCRIPTION PT2202 is a highly integrated current mode PWM controller ， providing low standby power and cost effective system solution for the sub 30W flyback converter applications. PWM switching frequency at normal operation is externally programmable and trimmed to tight range. At no load or light load condition, the IC enters ‘Green Mode’ operation to minimize switching loss and low standby power and high efficiency is thus achieved. PT2202 also features low VDD startup current which also contributes to low standby power. The built in LEB on the current sense input removes the signal glitch due to snubber circuit diode reverse recovery and will greatly reduce the external component count and system cost in the design. Rich protection is implemented in PT2202 including cycle-by-cycle current limiting (OCP), over load protection (OLP), VDD over voltage clamp and under voltage lockout (UVLO). Gate drive output is cla...
供应迟滞电流模式降压型LED驱动芯片IC-MT7900
信息内容：MT7900是一款迟滞电流模式降压型LED驱动芯片，同时支持DC和AC输入电压，具有极宽的输入电压范围，14VDC-450VDC或85VAC-265VAC，MT7900采用恒定关断时间工作模式，无需环路补偿，内部集成具有专利技术的线电压补偿机制，输出电流精度达到正负2%，输出电流可达1A，可驱动多达350颗LED，效率高打92%，内有独特的抖频技术，有效降低EMI干扰，芯片内部集成LED开路，LED短路保护，芯片过热保护等保护机制，提高了系统的可靠性，内部集成了10V和12V稳压输出，方便外围电路应用，进一步降低系统成本。 MT7900支持隔离及非隔离交流转直流的应用，能直接从交流市电供电，用于隔离设计时，直接从源极端检测，无需光藕。 产品性能： 输入电压范围：14VDC-450VDC或85CAV-265VAC 可驱动多达350颗LED 可支持超过1A恒电流输出 集成线电压补偿机制，输出电流精度可达正负2% 高达85%-92%的效率 自有的抖频技术，降低EMI干扰 无需外部12V稳压二极管，降低整板成本 LED开路，短路保护，芯片过温保护 可用于隔离应用和分隔离应用 采用SOT23-6封装 产品应用： LED日光灯，LED路灯 LED信号灯，装饰灯 LED RGB背光驱动
