Under minal voltage and minal load,the ripple and ise are as follows when measure with Max.Bandwidth of 20MHz and parallel 47uF/0.1uF,crossed conneed at tting point.
电压波纹/噪声
Voltage Ripple and ise(Max)
+12Vdc 150m V p-p
3.4上升时间/Rise time:
当输入220Vac和输出负载时时间为40mS。
40 mS Max. At 220Vac input and output MAX load.
3.6保持时间/Hold up time.
当输入220Vav和输出负载时时间为40mS.
40 min.at 220Vac input and output Max.Load.
3.7效率/Efficiency:
当230Vac输入电压时,,1/4,1/2,3/4和满载计算平均效率,小60%。
60% Min.At 115/230Vac input voltage,1/4,1/2,3/4and full load calculation average efficiency.
型号/Our model: KYD-121000G
客户/Customer:
日期/Date:
样品编号/Sample :
4.保护功能/PROTEION FUNION:
短路测试/Short circuit tt:
该电源供给器在短路解除时能正常工作恢复。
The power supply mill be auto recovered when short circuit faults remove.
5、环境要求/ENVIRONMENTAL REQUIRENET:
5.1工作温度/Operating Temperature:
0℃-40℃,满载,正常工作.
0℃to 40℃,Full load,rmal operation.
5.2储藏温度/Storage Temperature:-20℃to 80℃
带外壳/With package
5.3工作湿度/Relative Humidity:
5%(0℃)~90%(40℃),72小时,满载,正常工作。
5%(0℃)~90%(40℃)RH,72Hrs,Full load,rmal operating.
5.4振动/Vibration
1.测试标准:国际电工电子委员会
Operating:IEC 721-3-3 3M3
5~9Hz,A=1.5mm
加速度(9~200Hz,Acceleration 5m/S2)
2.运输/Transportation:
IEC 721-3-2 2M2
5-9Hz,A=3.5mm
9~200Hz,加速度Acceleration=5m/S2
200~500Hz,加速度Acceleration=15m/S2
型号/Our model: KYD-121000G
客户/Customer:
日期/Date:
样品编号/Sample :
3.轴向振动/Ax,10 cycl per axis.
在测试过程中不能出现性的损坏.
permanent damage may occur during tting.
在电源开启和关闭后,样机能够恢哦初条件.
The SAMPLE has to its original situation after power power off/on.
5.5跌落试验/Dropping packed:
插墙式跌落高度为0.8米、桌面式跌落高度为500mm;
1M for wallmount te and 760mm for dk te as above dcribed.
测试台面是厚13mm的夹木板,离地面高19-20mm
The horizontal surface consists of hardwood at least 13mm thick,mounted on two layers of plywood each 19mm to 20mm thick,all supported on a concrete or equivalent n-rilient floor.
6、要求/SAFETY REQUIREMENT:
6.1.:合标准CE(EN60950-1),AS/NZS:60950-1
Safety:accord withCE-(EN60950-1),AS/NZS:60950-1
6.2高压/DIELERIC STRENGTH Hi-pot:
初级对次级/Primary to secondary:1000Vac 10mA/3S for te tt.