SMC AS系列速度控制阀的使用注意
1）安装时，应事先将配管吹净，应确认阀的流动反向没有装反。
2）接头螺纹用手拧上后，用工具再旋2~3圈，安装力矩要适当。
3）管接头螺纹上，一般都已涂好密封剂，通常可使用2~3次。管螺纹如拧得过紧，密封剂会被挤出，应清除。
4）顺时针旋转调节手轮，节流阀是逐渐关闭的。使用时，应从全闭状态逐渐打开，将气缸调至要求的速度。
5）速度控制阀的调节圈数不得过给定值，以免损坏针阀。
6）万向式速度控制阀，不宜用于经常回转的情况
7）速度控制阀可能存在微漏，难于对气缸进行低俗控制。同时，不得把速度控制阀当做截止阀使用。
8）应尽量靠近气缸安装，以控制性能，否则，响应时间过长，气缸速度有可能难于控制。当气缸至速度控制阀之间的配管容积大于气缸容积时，就很难控制气缸速度。也说明气缸缸径越小，速度控制越难
| AS1001F-01 | AS2201F-01-04S-X26 | AS2211FM-01-04 | AS3201F-03-08S | AS4201F-04-12N |
| AS1001F-01K | AS2201F-01-06 | AS2211FM-01-04S | AS3201F-03-08SD | AS4201F-04-12S |
| AS1001F-03 | AS2201F-01-06K | AS2211FM-01-06 | AS3201F-03-08SK | AS4201F-04-12SD |
| AS1001F-03K | AS2201F-01-06S | AS2211FM-01-06S | AS3201F-03-08SKN | AS4201F-04-12SK |
| AS1001F-04 | AS2201F01-06S | AS2211FM-01-08 | AS3201F-03-08SK-X264 | AS4201F-04-12SN |
| AS1001F-04-3 | AS2201F-01-06SD | AS2211FM-01-08S | AS3201F-03-08SN | AS4201F-04-12ST |
| AS1001F-04-3-X250 | AS2201F-01-06SK | AS2211FM-01-23 | AS3201F-03-08ST | AS4201F-04-12S-X214 |
| AS1001F-04-5-X250 | AS2201F-01-06SK-X264 | AS2211FM-02-04S | AS3201F-03-08S-X214 | AS4201F-04-12S-X95 |
| AS1001F-04D | AS2201F-01-06SN-X36 | AS2211FM-02-06 | AS3201F-03-08S-X214A | AS4201F-04-12W2 |
| AS1001F-04K | AS2201F-01-06ST | AS2211FM-02-06S | AS3201F-03-08S-X95 | AS4201F-04-13S |
| AS1001F-04N | AS2201F-01-06S-X214 | AS2211FM-02-08 | AS3201F-03-08W2 | AS4201F-04-13SK |
| AS1001F-04T | AS2201F-01-06S-X242 | AS2211FM-02-08S | AS3201F-03-09W | AS4201FE-04-10SK |
| AS1001F-06 | AS2201F-01-06S-X26 | AS2211FM-02-10 | AS3201F-03-10 | AS4201FE-04-12SK |
| AS1001F-06-3 | AS2201F-01-06S-X36 | AS2211FM-02-10S | AS3201F-03-10K | AS4201FG-04-10 |
| AS1001F-06-3-X214 | AS2201F-01-06S-X95 | AS2211F-N01-01S | AS3201F-03-10N | AS4201FG-04-10S |
| AS1001F-06D | AS2201F-01-06W2 | AS2211F-N01-07S | AS3201F-03-10S | AS4201FG-04-12 |
| AS1001F-06K | AS2201F-01-06-X36 | AS2211F-N02-08S | AS3201F-03-10SD | AS4201FG-04-12S |
| AS1001F-06N | AS2201F-01-06-X95 | AS2211FPG-01-06 | AS3201F-03-10SK | AS4201F-N04-10 |
