Multilink Universal 多合一开发接口
特性:
· 从PC到Multilink的U接口允许快速，方便的编程和调试--通过方便和兼容的U接口。
· U供电 -无需单独的电源供应(目标烧写小于1mA)。
· 目标电压：1.6V的-5.25V
· 目标频率：16KHz-50MHz (适用于HCS08，RS08，CFV1，或HCS12X)
· 支持 HCS08，RS08，HCS12，HC12，ColdFire V1/+V1，ColdFire V2-4，Qorivva MPC55xx/56xx，以及 Kinetis ARM 微处理器系列。
· 自动频率检测+适应，用于HCS08设备。
· 自动频率检测，用于HC(S)12(X)设备。
· 对RS08设备在RET line生成烧写电压
P&E’s U Multilink Universal is an all-in-one development interface which allows a PC accs to the Background Debug Mode (BDM) or JTAG interface on Frecale HCS08, HC(S)12(X), S12Z, RS08, ColdFire V1/+V1, ColdFire V2-4*, Qorivva 55xx/56xx, and Kinetis ARM microcontrollers. It connects between a U port on a Windows machine and the standard debug connector on the target. The Frecale microcontrollers are supported via the multiple headers located on the U Multilink Universal. The product photos to the left of this page show how the headers can be accsed by simply flipping open the plastic case. Ribbon cabl suitable for a variety of architectur are included.
Supported Frecale Devic:
· Kinetis
· Qorivva MPC55xx/56xx
· ColdFire +V1/ColdFire V1
· ColdFire V2/3/4
· Power Architecture PX Seri
· HC(S)12(X)
· S12Z
· HCS08
· RS08
· DSC
By using the U Multilink Universal, the user can take advantage of the background debug mode to halt rmal procsor execution and use a PC to control the procsor. The user can then directly control the target’s execution, read/write registers and memory valu, debug code on the procsor, and program internal or external FLASH memory devic.
The U Multilink Universal works with P&E Microcomputer System's in-circuit des and flash programmers to allow debug and flash programming of the target procsor. For many of the supported procsors, P&E has a set of interface librari allowing the user to write their own Windows based application which interacts with P&E's debug interface. IAR, Codourcery, Keil, and CodeWarrior software all support the use of P&E's U Multilink Universal to develop and debug with Frecale's Kinetis ARM devic.
This interface is U 2.0 compatible, and it is also backwards compatible with U 1.1 ports.
TE: For a much faster all-in-one development interface which can also supply power to the target, please see the U Multilink Universal FX.
For production usage, see either the Cyclone PRO or Cyclone MAX stand alone programmer and debug interface, depending on which procsor you are working with. See the 单片机#comparison#comparison" _xhe_href="https://www.hi1718.com/member-center/sell/pub-pro.aspx?clid2=null&clid1=725&clid0=703&clname=电子元器件>单片机#comparison#comparison">comparison chart below.
FEATUR:
· U interface from PC to Multilink allows for fast, easy programming and debugging -- with the ease and compatibility of the U interface.
· Draws power from U interface-- separate power supply required (draws ls than 1mA from the target).
· Target Voltage: 1.6V-5.25V
· Target Frequency: 16Khz-50Mhz (appli to HCS08,RS08,CFV1, S12Z, or HCS12X only)
· Compatible with HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC55xx/56xx, and Kinetis ARM famili of microcontrollers.
· Includ U cable, Te A Male to Te B Male, 6-ft.
· Auto-frequency detection + trimming capabiliti for HCS08 devic.
· Auto-frequency detection for HC(S)12(X) devic.
· Generat programming voltage on RET line for RS08 devic.
Includ:
· One (1) U 2.0 High Speed Cable, Te A to Te B, 6-ft.
· One (1) 6-pin 0.100" pitch ribbon cable for connecting to RS08, HCS08, HC(S)12(X), S12Z, ColdFire V1/V1+ targets
· One (1) 14-pin 0.100" pitch ribbon cable for connecting to Qorivva MPC55xx/56xx targets
· One (1) 26-pin 0.100" pitch ribbon cable for connecting to asynchrous ColdFire V2/V3/V4 targets
· One (1) 20-pin 0.100" pitch ribbon cable for connecting to Kinetis ARM targets
· One (1) 20-pin 0.050" pitch ribbon cable for connecting to Kinetis ARM targets
