超声波测距仪是 完全适用于家庭装修、买空调时计算面积体积、房地产代理商或 建筑工人 所必须的、需要的快速测量房间和房间面积的工具， 超声波测距仪能够测量直线距离从0.50M到18M。(1.5英尺—60英尺) 超声波测距仪是利用发射超声波到被测物体，然后计算超声波往返时间来确定测量距离的。
参考参数：
测量范围：50厘米~18米
误差:千分之五
分辨率:0.01米
测量距离:18米
距离之和:180.00米
计算面积:18×18平方米
计算体积：1800.0立方米
电池：9v
发射频率：40kHz
度：±0.5%
分辨率：0.01m
工作温度：0°C ~ 50°C
产品介绍：
超声波测距仪在国外被称之为“电子卷尺”，适用于建筑、装修、工程等场所，能够做到传统卷尺力所不及的测量。本店销售的超声波测距仪根据厂家提供的数据显示已经是目前国际上性能比较好的产品，而且在欧美市场的占有率相当高，比起其他品牌的测距仪在超声波发射角、抗干扰处理等方面上有了明显地差别。
型号:CP-3007
出口产品,英文说明书!如果需要中文说明书的以电子文档方式提供.
红外测距仪 超声波测距仪 工程测距 无线测距 真方便！
测量时注意事项：
1.超声波测距仪测试的是障碍物离机器底部的距离，而不是顶部距离，如果以顶部为准，你会发现显示距离与实际距离永远有那么10几cm的误差，呵呵。
2.测量时机身与墙壁尽量保持垂直，尤其是所测距离较远时，越垂直，测量数据越高，反之斜度越大，误差越大。长距离测量时建议开一下激光定位以尽量保持垂直
新款CP3007激光测距仪 超声波测距仪
详细中文使用说明书：
CP-3007超声波测距仪使用指南
准备
安装电池
你的测距仪需要9V的电池。为了更好的使用和延长寿命，我们建议你使用碱性的电池。
请根据以下步骤安装电池：
1. 按照电池室箭头的方向去放；
2. 盖是推滑开的，电池室里有正负（+和-）两极，
3. 打开盖子
4. 当显示电量低时或者是测距仪不能运行时，请更换电池。
警示：如果是一个月或者是一个月以上不用，请把电池取出，以免电池长时间不用漏液损坏仪器。
测距仪的稳定化处理：
此仪器对温度和湿度很敏感，在使用之前，等15—30分钟直到测距仪稳定到室温。
使用
测距仪的开关：
要打开此仪器，请按“MEASURER”即使在黯淡的光线下也能很容易显示屏幕，等电压稳定了，就可以看到当时的环境温度。
30秒如果不用就自动关闭。
测量时：
1.请按一下“MEASURE”，此仪器的雷达将会测出仪器到达所要测的另一端。
2.使仪器的底部靠近墙壁，大概是天花板到地板的距离。确保你测量的距离之间没有障碍物，你的头或者你的手不要在测量仪的前面。
3.重复按“FEET”或者“METER”， “FEET”表示以英尺测量，或者是出现“METER”表示以米测量。
说明：
测量仪的显示一般是在30秒左右，如果你更换另一个模式也是要30秒左右。
如果你测量的范围小于2英尺（0.5米）或者是大于60英尺（18.288米）将会显示“ERROR”
测量小秘诀：
有些窗帘可以吸收声波，导致测量仪测量不准。如果你在有窗帘的室内进行测量的话，请先把窗帘放到窗户的另一面，还要把窗户关上。
如果测量的距离中有障碍物的话，那超声波测量出来的数据是不正确的，比如说桌子，椅子，或者其他的障碍物。如果你不确定你测量的是否正确，那你就从不同的角度进行多次测量。
如果你测量的不是平整的地方或者是很窄的角落，那你得出的数据就是有误的。
如果要测量的距离大于60英尺（18.288米）那就选择房子的中间的一点，比如说:从中点向每一面测量，然后加起来就可以了。
减小测量误差：
1. 按照这些步骤用“测量”来衡量一个尺寸
2. 按一下“STORE”键，你就可以把测量的数据存储在内存卡M1，M2或者M3卡里面。
3. 如果有必要，就重复上面的和第二步骤去存储数据。
4. 如果想把数据存储在哪个内存卡，就按M1，M2或者M3卡。这样数据就存在里面了。
5. 如果想存储新的数据的话，那就直接把原来的数据删除就可以了。
6. 如果要删除所有的数据的话，那就按“ALL MEMORY CLEAR ”按住3秒，然后全部的数据还有M1，M2, M3之类的都会暂时消失。
注意： 删除后日期和声音是不能保存的
测量音量：
想测量住房的音效，先测量高度，宽度，长度，然后储存每个数据到不同的内存卡请看到“Saving a Measurement”,然后按“VOLUME”，音效的计算和存储就出来了。
测量面积：
根据以下步骤找两个空的存储空间：
1. 测量的高度和宽度就存储在M1和M2的内存卡上，按“AREA”“M1”和“M2”,数据就存储了。
加减乘除的存储
1. 测量出来的任何两个尺寸，保存在M1和M2，
2. 按“ALL MEMORY CLEARE”键
3. 按“M1”加“M2”加其他要加的数据或者是按“M1”减“M2”减其他要减的数据，这样要加的或者要减的数据就出来了。
4. 如果想存储另外的数据或者是想清除内存请按“ALL MEMORY CLEARE”就可以了。
使用激光：
要使用激光，请按“LASER”，如果5秒钟不动的话会自动关闭激光的功能。
规格：
电池：1个9V的电池。（不包括）
测量仪的单位是英尺和米。
度：0.005+1
频率：40千赫
测量范围：0.50到18.288米
典型的规格，个别有可能会改变，规格如有更改,恕不另行通知改善。
注意：
激光发射的650海里为可视激光波长。
别盯着激光光束看,也不要用激光射任何人的眼睛
CP-3007 Ultrasonic Distance Measurer OWNER'S MANNUAL
PREPARTION
INSTALLING BATTERIES
You measurer requires 9V battery(not supply) for power.
For the best performance and life,we recommend alkaline battery.
Follow these steps to install a battery.
1.Slide the battery compartment cover in the direction of the arrow to remove it.
2.Snap the battery in the compartment.As indicated by the polarity symbols(+and-)marked inside.
3.Replace the cover.
4.When Low Battery Icon appears or the measurer stops operating properly,replace the battery.
Caution: If you do not plan to use the measurer for a month or more,remove the battery ,Battery,Batteries can lesk chemicals that can destroy electronic parts.
STABILIZING THE MEASURER
You measurer is sensitive to changes in temperature and humidity.Before you use the measurer,wait about 15~30minutes for it to stabilize to the current room's temperature.
OPERATION
TURNING THE MEASURER ON/OFF
To turn on the measurer,press MEASURER, can light up the display screen for easy viewing even in a dimly lit area.After power on,the unit display current Environment temperature.
The measurer turn itself off if no key is pressed within about 30 seconds.
TAKING A MEASUREMENT
1.Pree MEASURE to turn on the unit.The measurer beeps then the distance between the measurer and the piont you measured appears.
2.Hold the bottom of measure flat against a wall,about hafway between the point you want to measure and that your head or hands do not block the front of the measure.
3.Repeatedly preesFEET/MERERuntilFEETappears(to measure in feet)or untilMETERappears(to measure in meter)
Notes:
The measurement appears for about 30 seconds(or longer if you press another key)
ERROR might appear if you try to measure a distance shorter than the range of 2 feet(0.5m)or longer than 60 feet(18.288 meters)
Measuring Tips
Some type of curtains and blinds can absorb sound waves.
Causing measurements to be inaccurate.If you are measuring distances in a room with curtains.Open the curtains before measuring the distance to a window behind them.Also,be sure that the window is closed.
If there is not clear path between the points where you are measuring.You might receive a false reading from sound waves bouncing off objects such as chair,tables and objects with uneven surfaces .If you are not sure if a measurement is correct,move slightly to one side then measure the distance again.
If the surface of a wall you are measuring is not sold and flat,or if you are measuring in a narrow corridor.You might receive a false reading.If this happens， use a sold surface to measure or move to the center of the corridor.To measure a distance longer than 60 feet(18.288 meters) measure from the center of the room toward each side.then add the two measurements.
SAVINGA MEASURENT
1.Follow the steps under"Taking a Measurement"to measure a dimension.
2.PressSTOREthen a memory key(M1,M2,M3).M and the number of the memory location you choose (1,2or3)appear and the measurer stores the reading in that memory location.
3.If necessary,repeat steps 1 and 2 to save up to three measurements.
4.To display measurement stored in a memory location,press that memory key (M1,M2,M3).The measurement stored in that memory location appears.
5.To delete a measurement stores in a memory location， simply store a new one in its place.
6.To clear all stored measurements,hold downALL MEMORY CLEARfor about 3 seconds,the measurer beeps and M and the number of the memory location you chose (1,2or3)disappears.
Note:Data of AREA of VOLUME can not be saved.CALCUATING VOLUME
To find the volume of a room.Measure the height,width and the length of the room and store each measurement in a different memory location(see"Saving a Measurement "),Then press VOLUME,The volume calculation result appear.
CALCULATIONAREA
Follow these steps to find the area of any two stored measurements
1.Measure the width and length of a room and store the measurements in M1 and M2(see"Saving a Measurement").Press AREA,M1 and M2,the area calculation appear.
ADDING/SUBSTRACTING STORED MEASURENTS
1.Measure any two dimension of a room and store the measurements in memory locations 1 and 2(see"Saving a Measurement")
2.PressALL MEMORY CLEAR.
3.Press M1,+M2,then +to add the measurements,or M1,-,M2,then-to subtract them.The value of the calculation appears.
4.To clear the display and do another measurement,pressALL MEMORY CLEAR.
USING LATER
To have a laser pointer,press LASER.The laser pointer disappears automatically after about five seconds
SPECIFICATIONS
Power lx9V
Unit of measurement Feet or Meters
Accuracy 0.5%+1digit(2-60ft)
Working Frequency 40KHz
Working Temperature 0℃ to 43℃
Range 2 to 60ft (0.50 to 18.288m)
Specifications are typical;individual units might vary.
Specifications are subiect to change and improvement without notice.
Caution:
The laser emitted from the unit is visible laster of 650nm wavelength
Don't stare in to the laster beam and also don't shoot laster beam to any other 's eyes.
Class II laser product Output<lmw
Notes:
The product has passed EN60825-1
Corresonding label is affixd on the back of the unit.
