- 产品品牌：
- Olympus NDT
- 产品型号：
- 5058PR
5058PR
The 5058PR High Voltage ultrasonic pulser-receiver is designed especially for test and measurement applications in sound-attenuating mediums. The pulser section can deliver up to 900 volts in an impulse type excitation pulse to appropriate low frequency transducers.
|
The Panametrics Model 5058PR High Voltage pulser-receiver is designed especially for ultrasonic test and measurement applications in attenuating mediums. The pulser section of the Model 5058PR can deliver up to 900 volts in an impulse type excitation pulse to appropriate low frequency transducers. The flexible receiver section provides switchable 40/60 dB gain with an additional 30 dB available from an integral low noise preamplifier. Four position high and low pass filters and 1 dB attenuation steps further optimize signal response. A full range of front panel controls permits discrete calibrated settings or continuous adjustments for easy and repeatable instrument setup. The unit is packaged in a rack adaptable 19" (483 mm) wide enclosure. Features & Benefits | |
|
• High voltage pulser, switched settings or continuously adjustable to 900 volts | |
Applications | |
|
Used with an analog or digital oscilloscope, the Model 5058PR can be the basis of a bench top measurement system for determination of material quality or properties. Flaw detection, time of flight, thickness, velocity, attenuation, and frequency content are investigated. The high voltage pulser and high gain receiver of the Model 5058PR make it particularly useful for applications that challenge the penetrating capability of conventional pulser/receivers in such materials as: |
Specifications
| PULSER 5058PR | |
| Pulse Type (Main Bang): | 0 to 20 KHz by external trigger pulse |
| Available Pulse Voltage: | -100 to -900 V continuously variable; -100, -200, -400 or -900 V switch selectable (meter measures available voltage on pulse storage capacitor) |
| Pulse Rise Time: | <40 nS @ 900 V, <10 n0S @ 100 V |
| Available Pulse Energy: | 11 to 890 microjoules, stepless, or 11, 44, 170, or 890 microjoules in selected pulse voltage positions |
| Damping: | 50 to 333 ohms, continuosly variable; 50, 100, 200, or 500 ohms switch selectable |
| Pulse Repetition Rate: | Internal: 20, 50, 100, 200, 500, 1 k or 2 kHz, switch selectable External: 0 to 2 kHz maximum |
| Sync Output Pulse: | TTL compatible, or +1v minimum into 50 ohms (occurs approx. 75hS before main bang when externally triggered). |
| External Trigger Input: | Edge triggered, accepts + or - input pulses. Zin = 50 or 500 ohms (internal switch) Max pulse height in: 65 V Rise time: <30 µS Pulse width: 0.1 µS <PW<4 µS Delay after Ext. Trig.: <200 nS |
| Mode: | Pulse-echo or thru-transmission, switch selectable |
| RECEIVER | |
| Maximum Receiver Input Power: | The maximum average power that receiver input can dissipate is 1W. Sine wave RF input should be limited to 10 V rms or 40 V rms at 25% duty cycle. |
| Input Impedance: | 500 ohms (linear range). Approx. 140 ohms for signals> linear range |
| Voltage Gain: | 40 dB or 60 dB (RL = 50 ohms), switch selectable |
| Phase: | Normal (0°) or inverted (180°), switch selectable |
| Bandwidth: | 10 kHz to 10 MHz (-3 dB) |
| High Pass Filters: | 0.01 (out), 0.03, 0.1, 0.3 or 1.0 MHz, switch selectable |
| Low Pass Filters: | 0.5, 1.0, 3.0, 5.0, or 10 MHz (out), switch selectable |
| Attenuation: | 0 dB to 80 dB in 1 dB steps |
| Attenuation Vernier: | 61 dB continuous (vernier can be switched off) with status LED. |
| Noise: | Typically 50 µV pk-pk referred to the input |
| Output Impedance: | 50 ohms in series with 10 µF |
| Maximum Signal Out: | ±0.5 V peak (RL =50 ohms), ±1 V peak (RL ≥ 1 K ohms) |
| AUXILIARY PREAMPLIFIER | |
| Input Impedance: | 100K ohm in parallel with 50 pF. |
| Maximum Input Power: | The maximum power that the receiver can dissipate is 1 W. |
| Gain: | 30 dB, non-inverting (RL = 500 ohms) |
| Bandwidth: | 600 Hz to 5 MHz (-3dB) |
| Noise: | 25 µV pk-pk referred to the input (Rs = 500 ohms, RL = 500 ohms) |
| Output Impedance: | 50 ohms in series with 4.7 µF |
| Maximum Output Level: | +/-0.5 V pk (RL = 500 ohms) |
| UNIT | |
| Signal Connectors: | BNC |
| Power Requirements: | 100, 120, 220, or 240 VAC selectable, 50-60 Hz, 45 watts maximum |
| Fusing: | 0.5A Slow Blow for 100 or 120 VAC, 0.25A Slow Blow for 220 or 240 VAC |
| Size: | 3.5" H x 16.7" W x 12.7" D 88.9 mm H x 424 mm W x 323 mm D |
| Weight: | 13.3 lbs (6 kg) |
| INTERIOR CONTROLS (USER ADJUSTABLE) | |
| Ext Trigger Termination: | 50 or 500 ohms, selectable (factory set to 50 ohms). |
| Ext Trigger threshold: | 0.1 to 1 V (factory set to 0.5 V) |
Standard Inclusions
The Model 5058PR is shipped with two BCB-58-4 cables, one 50 ohm terminator, application detachable power/mains cord, and operating manual. An optional rack-mount kit is available and should be specified at time of ordering.
*All specifications are subject to change without notice
