CBF系列防爆轴流风机

CBF防爆轴流风机，CBF-300防爆轴流风机，CBF-400防爆轴流风机，CBF-500防爆轴流风机，CBF-600防爆轴流风机。

巨祥防爆公司网站https://www.jxfb.cn/商铺网站https://www.jexfb.com/ 电话    手机：.,

【型号：CBF-300，风叶直径300mm，功率0.18KW,主轴转数1450rpm,风量2280;】
【型号：CBF-400，风叶直径400mm，功率0.37KW,主轴转数1450rpm,风量2880;】
【型号：CBF-500，风叶直径500mm，功率0.55KW,主轴转数1450rpm,风量5700;】
【型号：CBF-600，风叶直径600mm，功率0.75KW,主轴转数1450rpm,风量8700;】
【型号：CBF-700，风叶直径700mm，功率1.1KW, 主轴转数1450rpm,风量10200;】

详细信息：
一、 CBF-300防爆轴流风机风机概述
CBF型防爆轴流式风机 ，用于输送易燃易爆的气体。叶轮由铝合金加工而成， 以防止在运转中引起火花, 电机采用隔爆型电机。
本系列风机适用于输送易燃易爆无腐蚀性气体，环境温度不得超过60℃。 广泛应用于一般工厂、仓库、办公室、住宅内通风换气或强暖气散热，也可在较长的排气管道内间隔串联安装以提高管道中的压力 ，卸下电机可做自由风扇。风机需带支架脚和电机电压，请订货时注明。
二、 CBF-300防爆轴流风机风机安装说明

◆ CBF-300防爆轴流风机安装前应详细检查风机是否有损坏变形，如有损坏变形，待修理妥善后，方可进行安装。
◆ CBF-300防爆轴流风机安装时要注意检查各不如部分有无松动，叶片与风筒间隙应均匀，不得相碰。
◆ CBF-300防爆轴流风机连接风口管道的重量不应由风机的风筒承受，安装时应另加支撑。
◆ CBF-300防爆轴流风机 在风机风口端必须装集风器，并安装防护网。
◆ CBF-300防爆轴流风机 风机底座必须与地基平面自然接合，不得敲打底座强制联接，以防底座变形，安装时应校正机座，加垫铁片、保持水平位置，然后拧紧地脚螺栓。
◆ CBF-300防爆轴流风机 安装完毕后，必须先进行实验，待运行正常后，才允许正式使用。
CBF-300防爆轴流风机主要技术参数

CBF-300防爆轴流风机，CBF-400防爆轴流风机，CBF-500防爆轴流风机，CBF-600防爆轴流风机。

A, CBF-300 explosion-proof axial fan blower Overview
CBF explosion-proof axial fans, used to transport flammable and explosive gas. The impeller is made of aluminum alloy processing to prevent spark caused in operation, motor flameproof motor.
Fans of this series is suitable for the transport of flammable and explosive non-corrosive gas, shall not exceed 60 ° C ambient temperature. Widely used in general factories, warehouses, offices, residential ventilation or the strong heating cooling interval longer exhaust pipe installed in series to increase the pressure in the pipe, remove the motor can be free fan. The fan bracket feet and motor voltage should bring, Please specify when ordering.
CBF-300 explosion-proof axial fan blower installation instructions

◆ CBF-300 explosion-proof axial fan installation should be a detailed examination of the fan if there is damage to deformation, deformation if damaged, to be repaired properly before installation.
◆ CBF-300 explosion-proof axial fan installation should pay attention to check the inferior part of the availability of loose leaves and duct clearance should be uniform, not touching.
◆ CBF-300 explosion-proof axial fan connected to the weight of the vent pipe should not bear fan hairdryer, plus support should be installed.
◆ CBF-300 explosion-proof axial fan in the fan outlet side must be installed a set of wind, and install protective nets.
◆ CBF-300 explosion-proof axial fan fan base and foundation plane natural bonding not beat base force join to prevent base deformation, the installation should be corrected base, plus horn piece, keeping the horizontal position, and then tighten the anchor bolts.
◆ CBF-300 explosion-proof axial fan is installed, you must experiment to be operating normally allowed to officially use.
The main technical parameters of the CBF-300 explosion-proof axial fan

CBF-300 explosion-proof axial fans, CBF-400 explosion-proof axial fans, CBF-500 explosion-proof axial fans, CBF-600 explosion-proof axial fans.