主要针对汽车空调各种漏点，整个系统快速100%不会误报，10-30分钟，100%找出各种泄漏点，代替加压力，洒水，荧光粉，拆系统在水中浸泡的原始方法。
工作原理，主要针对氟的化学成份，稀浓度，抓捕分析，在空调系统中追捕氟的泄漏量，氟的颗粒量少0.01的分之一，100%分析。
原理Principle
利用一个高的真空泵，将空调系统可能微泄的氟利昂吸入探测器，探测器采用高频磁场低压电离的工作方式,吸入微量的氟利昂,其液晶显示数字立刻上升，同时蜂鸣器报警。
by using a high vacuum pump, the micro leak freon can to inhale detector, detector adopts low-voltage high frequency magnetic field ionization ways of working, inhaled trace of freon, the liquid crystal display Numbers rise immediately, at the same time a buzzer alarm.
技术The core features
1)持续稳定的工作
2)能检测0.01ppm的氟利昂,相当于0.05克/年的泄漏量。
1) stable and reliable work;
2) the highest accuracy to detect 0.01 PPM of freon, equivalent to 0.05 g/leakage of the year.
典型效果Tical effect
1） 蒸发器检漏，在确定漏点前，无须拆风口，拆仪表盘；
2） 可以检测到老化的空调软管渗漏（肥皂泡、荧光剂测不到的漏点）；
3） 不制冷的汽车空调系统，不需要添加，即可检测。
4） 看不到气泡的气门芯泄漏1秒钟即可；
5） 半小时一辆车，检测完毕，无须拆系统，无须水中浸泡；
1) the evaporator leakage, before determining leak point, do not need to diantle tuyere and tear open the dashboard;
2) can detect leakage of air conditioning hose aging (soap bubbles, fluorescent agent can't measuring leak point);
3) no refrigeration automobile air conditioning system, don't need to add freon, can detect.
4) 1 second can determined the leak valve core;
5) Half an hour to complete the detection of a car, no need to diantle the system, no water immersion;
使用介绍Method of use
蒸发箱，只要5分钟，关闭空调，把探测器放在蒸发箱下面的风口，数字上升3-10左右，确定有漏。
the evaporation box: Five minutes is enough. Turn off the AC, and put the probe in tuyere on the bottom of the evaporation tank, figure up 3-10 or so, determine how leakage
在确定漏点前，无需拆风口before determined the leak point, with no need to open panel
压缩机：只要5分钟，探头在机体，轴头来回3-5次，数字上升5-15左右，确定有漏。
the compressor: Five minutes is enough.. Place the probe in the body and turn the head back and forth 3-5 times, and if the number rises by 5-15,then the leak is determined.
冷却箱，10分钟，把探头随着箱体结构来回均匀探测移动，数字上升，3-30左右，确定有漏。
the cooling tank: It takes about ten minutes. Move the probe with the body structure of the cooling tank at steady pace, and if the number rises by 3-30, then the leak is determined.
剩余管道的接头处10分钟把探头随管道走向来回3-5次，数字上升5-30左右，确定有漏。
the remaining of pipe joint: This step takes around ten minutes. Move the probe along the pipeline back and forth 3-5 times, and if the number rises by 5-50, then the leak is determined.
